Endress+Hauser Proline Promag 50P User Manual

TI047D/24/ae/07.06
Technical Information
Proline Promag 50P, 53P
Electromagnetic Flow Measuring System
Flow rate measurement in chemical or process applications
Application
Electromagnetic flowmeter for bidirectional
measurement of liquids with a minimum conductivity
of ≥ 5 µS/cm:
• Acids and caustic solutions
•Paints
•Pastes, mashes
• Water, wastewater etc.
• Flow measurement up to 44,000 GPM
(9600 m
3
/h)
• Fluid temperature up to 356°F (180°C)
• Process pressures up to 580 psi (40 bar)
• Fitting lengths to DVGW/ISO
Application-specific lining materials:
• PTFE und PFA
Approvals for hazardous area:
• ATEX, FM, CSA, TIIS
Connection to process control system:
•HART
®
, Profibus
®
DP/PA, FOUNDATION™
Fieldbus, MODBUS
®
RS485
Your benefits
Promag measuring devices offer you cost-effective flow
measurement with a high degree of accuracy for a wide
range of process conditions.
The Proline transmitter concept comprises:
• Modular device and operating concept resulting in a
higher degree of efficiency
• Software options for batching, electrode cleaning and
for measuring pulsating flow.
• Uniform operating concept
The tried-and-tested Promag sensors offer:
•No pressure loss
• Not sensitive to vibrations
• Simple installation and commissioning

Endress+Hauser Proline Promag 50P Specifications

General

Device Type	Electromagnetic Flowmeter
Housing Material	Aluminum, stainless steel
Measuring Principle	Electromagnetic induction
Measuring Range	0.1 m/s to 10 m/s
Process Pressure	Up to 40 bar (depending on nominal diameter)
Output Signal	4-20 mA HART, Pulse, Frequency, Alarm
Power Supply	24 V DC
Degree of Protection	IP67
Lining Material	PTFE
Electrode Material	Stainless Steel
Material	Stainless Steel
Communication	HART
Nominal Diameter	DN 15 to 600 (½ to 24")

Summary

Proline Promag 50P, 53P Technical Information

Application Details and Use Cases

Details on suitable applications and media for the flowmeter.

Function and System Design

Electromagnetic Measuring Principle

Explanation of the Faraday's law of induction used for flow measurement.

Measuring System Components

Overview of transmitter and sensor versions and their specifications.

Output Signals and Interfaces

Promag 50 Output Options

Current, pulse/frequency outputs for Promag 50 transmitter.

Promag 53 Output Options and Interfaces

Promag 53 Output Options

Current, pulse/frequency outputs for Promag 53 transmitter.

Electrical Connection and Power Supply

Wiring Diagrams and Power Requirements

Diagrams for electrical connections and power supply specifications.

Terminal Assignments

Promag 50 and 53 Terminal Configurations

Mapping of inputs/outputs to terminal numbers for Promag 50 and 53.

Supply Voltage and Potential Equalisation

Power Supply and Equalisation

Requirements for supply voltage and potential equalisation.

Grounding and Piping Installation

Metal Piping Grounding Guidelines

Instructions for grounding metal pipes to prevent interference.

Performance Characteristics

Operating Conditions and Measured Error

Reference conditions, maximum error, and repeatability specifications.

Installation Conditions

Mounting Location Guidelines

Installation Guidelines

Pump Installation Precautions

Orientation and Features

Vertical and Horizontal Orientation

Mounting and Supports

Vibration and Support Requirements

Installation Runs and Adapters

Inlet/Outlet Runs and Adapters

Process Conditions and Temperature Limits

Medium Temperature Range

Permissible medium temperature based on tube lining.

Material and Vacuum Specifications

Conductivity, Pressure, and Vacuum Ratings

Installation Variants

Panel and Pipe Mounting Options

Human Interface

Display, Operation, and Language

Certificates and Approvals

Compliance and Certifications

Information on Ex approvals, CE, communication protocol certifications, and standards.

Ordering Information

Promag 50P and 53P Ordering Codes

Selection codes for configuring Promag 50P and 53P flowmeters.