EasyManua.ls Logo

Engbo MAXI 31 - User Manual

Engbo MAXI 31
43 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
ENGBO AS – et selskap i Engbo-gruppen
BESØKSADRESSE: Wirgenesvei 7, 3157 Barkåker POSTADR: Postboks 2288 Postterminalen, 3103 Tønsberg
E-MAIL: support@engbo.no WEB: www.engbo.no TLF: +47 33 00 31 50 FAKS: +47 33 00 31 60
USER AND INSTALLATION
MANUAL
ENGBO ANCHOR WINCH
MAXI 31
MAXI 32
MAXI 34-series
MAXI 38
MAXI 40
Engbo MAXI products fit most boat models
Rev. 7-2010-01-04
According to NS-EN ISO 9001:2000
FCC ID: R78-RC-01
Part no. 117-00036 R78-MCU-01

Table of Contents

Other manuals for Engbo MAXI 31

Preview: User Manual
User Manual45 pages

Questions and Answers

  • C
    Christopher MillerAug 1, 2025
    What to do if Engbo MAXI 31 windlass does not work or pulls very poorly?
    • J
      John SerranoAug 1, 2025
      If your Engbo boating equipment windlass isn't working well, start by checking the main power supply. Measure the voltage in the battery cables at the point where they connect to the windlass while it's running. If the voltage is less than 10.5V, investigate the cause. Inspect all connection points, including the main switch, fuse, battery shoes, and the battery's overall condition and voltage. If the voltage is above 10.5V but the motor still doesn't work, the electronic protection function might have shut it down due to prolonged use or overload. Let it cool down for about 20 minutes before trying again.
  • C
    Carlos GomezAug 9, 2025
    How to troubleshoot Engbo MAXI 31 if the windlass is completely dead?
    • J
      Jacob ReedAug 9, 2025
      If your Engbo boating equipment windlass is completely dead, begin by verifying that the main switch is in the ON position and the fuse is intact. Ensure all connection points are making proper contact and that all connections align with the diagrams provided in the manual. Finally, confirm that there's sufficient voltage being supplied to the windlass motor.
  • T
    tlarsonAug 15, 2025
    Why Engbo Boating Equipment windlass will not drop anchor and only winds in for 3 s?
    • A
      Angela ThompsonAug 15, 2025
      If your Engbo boating equipment windlass only winds in for 3 seconds and refuses to drop anchor, check that the connections to the electronic control unit (1, 2, and 3) match the diagram. Try swapping connections 1 and 3; this should restore correct function.
  • R
    rrodriguezAug 23, 2025
    What to check if auto stop function does not work on Engbo MAXI 31?
    • S
      Steven SanchezAug 23, 2025
      If the auto stop function isn't working on your Engbo boating equipment, specifically on rope windlasses, start by checking the following: - Ensure the connections to points 4, 5, and 6 are correctly configured according to the diagram. - Verify that the voltage to the emitter (between points 4 and 6) exceeds 10 V DC. - Confirm that the auto stop wires are properly positioned. - Check that the auto stop emitter is at the correct distance from the rope. If the voltage is adequate and the emitter distance is correct, but the lamp remains unlit, the emitter likely needs replacement.

Summary

Introduction

Operating Instructions

Anchoring and Setting Off Procedures

Step-by-step guide for anchoring, landing, and departing.

Wireless Remote Control Usage

Detailed instructions for using the wireless remote, including anchor up/down and indicators.

Engbo Anchor System Overview

MAXI Windlass Features

General description of Engbo MAXI windlasses and their free-fall capability.

Electronic Control Unit

Details about the modern electronics, integrated receiver, and protection systems.

Switch Panel Options

Overview of standard touch panel and wireless remote control options.

Installation Guidelines

General Positioning and Mounting

Positioning the windlass for optimal rope storage and friction.

Anchor Bracket and Hull Conduit

Fitting anchor brackets and hull conduits for rope guidance.

Safety Line and Auto Stop Setup

Securing the anchor with a safety line and setting up the auto stop function.

Troubleshooting and Maintenance

Auto Stop Function Adjustment

How to adjust and ensure the proper function of the auto stop system.

Routine Maintenance Procedures

Procedures for replacing batteries, checking wear, and winter storage.

Troubleshooting Common Faults

Steps to diagnose and resolve common windlass operational issues.

Engbo MAXI 31 Specifications

General IconGeneral
BrandEngbo
ModelMAXI 31
CategoryBoating Equipment
LanguageEnglish

Related product manuals