Engbo MAXI 40 User Manual

ENGBO AS – et selskap i Engbo-gruppen
BESØKSADRESSE: Wirgenesvei 7, 3157 Barkåker POSTADR: Postboks 2288 Postterminalen, 3103 Tønsberg
E-MAIL: support@engbo.no WEB: www.engbo.no TLF: +47 33 00 31 50 FAKS: +47 33 00 31 60
USER AND INSTALLATION
MANUAL
ENGBO ANCHOR WINCH
MAXI 31
MAXI 32
MAXI 34-series
MAXI 38
MAXI 40
Engbo MAXI products fit most boat models
Rev. 7-2010-01-04
According to NS-EN ISO 9001:2000
FCC ID: R78-RC-01
Part no. 117-00036 R78-MCU-01

Engbo MAXI 40 Specifications

General

Brand	Engbo
Model	MAXI 40
Category	Boating Equipment
Language	English

Summary

Introduction to Engbo Anchor Windlass Manual

General Procedures for Using Engbo Maxi Windlasses

Important Safety & Operational Points

Critical safety, installation, and operational points for windlass use.

Operating Instructions

Preparation Before Anchoring

Steps to prepare the boat and windlass before dropping the anchor.

Landing

Instructions for anchoring and securing the boat to land.

Setting Off

Procedures for raising the anchor and departing from shore.

Wireless Remote Control Operations

How to use the wireless remote for anchor windlass operation.

Anchor Down

Process of lowering the anchor using the remote control.

Anchor Up

Instructions for raising the anchor using the remote control.

Power Indicator Information

Meaning of remote control indicator lights.

Forced Operation of the Windlass

How to manually override windlass for specific situations.

Engbo Anchor System Overview

Electronic Control Unit

Components and functions of the electronic control unit.

Switch Panels

Standard Touch Panel

Details the standard watertight touch panel for operation.

Wireless Remote Control Types

Explains features and types of wireless remote controls.

Installation – General

Anchor Bracket

Role and fitting of the anchor bracket.

Hull Conduit / Line Guide

Purpose and installation of hull conduits for rope guidance.

Anchor Rope Specifications

Details specifications and importance of the original Engbo anchor rope.

Wireless Remote Setup

Fitting Antenna

Steps to install the aerial for the wireless remote control.

Coding Wireless Remote Control

Control Unit Code Mode

Steps to set the wireless control unit into coding mode.

Receiver Unit Code Mode

Instructions for preparing receiver to accept new remote codes.

Dimensional Sketches

Maxi 31/40 Series Dimensions

Drawings and dimensions for Maxi 31 and 40 series windlasses.

Maxi 32 Series Dimensions

Drawings and dimensions for Maxi 32 series windlass.

Maxi 33 Series Dimensions

Drawings and dimensions for Maxi 33 series windlass.

Maxi 34 Series Dimensions

Drawings and dimensions for Maxi 34 series windlasses.

Maxi 38 Series Dimensions

Drawings and dimensions for Maxi 38 series windlass.

Technical Specifications

Motor Output, Power, and Fuses

Specifies motor output, power consumption, and recommended fuses.

Rope, Chain, and Anchor Specs

Details rope/chain types, anchor weights, and suggested boat sizes.

Performance Parameters

Lists pulling power, pulling speed, and recommended battery capacity.

Unit Weight and Auto Stop

States unit weights and confirms auto stop function availability.

Equipment and Fitting Reference

Lists standard/supplementary equipment and refers to fitting sections.

Electrical Wiring

Standard Touch Panel Installation

Details installation of the standard touch panel switch.

Connecting the Switch Panel

Step-by-step guide for connecting the switch panel.

Connecting Auto Stop Switch

Instructions for connecting the auto stop switch for rope windlasses.

Connecting Motor and Battery Cables

Guidance on connecting motor and battery cables to the electronic unit.

Electrical Wiring Diagram

Fitting Instructions

General Installation Information

Advice on positioning and space requirements for installation.

Hinged Platform Roller Fitting

Guidance on fitting a hinged platform roller.

Line Guide in the Stern

Instructions for installing a line guide in the stern.

Hull Conduit with Pulleys

Describes the component used for leading rope through hull.

Anchor Bracket Selection

Platform Roller Examples

Examples of standard and hinged platform rollers.

Tilt Bracket and Anchor Davit

Examples of tilt brackets and anchor davits.

Fitting Maxi 31

Fitting Maxi 32

Maxi 32 Box Fitting

Fitting Maxi 33

Fitting Maxi 40

Fitting Maxi 34-V

Fitting Maxi 34-D

Fitting Maxi 34-G

Fitting Maxi 34-S

Fitting Maxi 34-H

Fitting Maxi 38

Auto Stop Function

Adjust Auto Stop Switch

How to properly adjust the auto stop switch for accuracy.

Fitting Auto Stop Indicators

Steps to install brass wire indicators for auto stop function.

Maintenance

Replace Wireless Remote Batteries

Instructions for replacing batteries in the wireless remote control.

Replacing Line Wheels

Steps for replacing the line wheels on the windlass.

Adjusting Line Guide Tension Spring

How to adjust the tension spring for the line guide.

Winter Storage Recommendations

Guidance for proper winter storage of the windlass.

Troubleshooting

High Current Installation Considerations

Installation Preface/Introduction

Intro to special considerations for high-current installations.

General Installation Advice

General advice and need for qualified personnel for high-current installations.

Battery Selection and Use

Guidance on selecting and understanding battery capacity and types.

Battery Cable and Lug Handling

Proper selection and mounting of battery cables and cable-lugs.

Battery Connection Procedures

Correct procedures and warnings for connecting battery cables.

Fuse and Fuse Holder Installation

Instructions for correctly connecting the fuse and fuse holder.

Main Switch Connection

Details on how to properly connect the main power switch.

Control Box Connections

Step-by-step guidance for connecting cables to the control box.

Motor Terminal Connections

Instructions for connecting motor terminal cables, including torque.