Envision R-410A Residential Installation Manual

32
ENVISION RESIDENTIAL INSTALLATION MANUAL
DIP Switch Settings
Priortopoweringunit,ensurethatallDIPswitchesonSW2&SW3aresetproperlyaccordingtothetablesbelow.
FACTORY SETUP DIP SWITCHES (SW3)
DIP
SWITCH
NUMBER
DESCRIPTION OFF POSITION ON POSITION
SW 3- 1
Dual Capacity/Single-Speed
Conguresthecontrolforsingle-speedcompressoroperationordualcapacityopera-
tion.
Dual Capacity Opera-
tion
Single-Speed Operation
SW 3- 2
Zoned/Finish on Second Stage
Thisswitchallowstheunittodownstagewiththethermostatwhenoffandnishwith
second stage when on. Finish on second stage reduces stage changing in recipro-
cating dual capacity compressors.
Normal - All Other
Systems
Finishon2nd-UnzonedDual
Capacity E Series or Premier
2Speed
SW 3- 3
No RPM/RPM
ConguresthecontroltomonitortheRPMoutputofanECM/ECM2blowermotor.
WhenusingIntelliZoneoraPSCfanmotor,thecontrolshouldbeconguredfor“NO
RPM” sensing.
PSCFan/RPMMoni-
toring Disabled
ECM-ECM2Fan/RPM
Monitoring Enabled
SW 3- 4
Electric heat and ECM2
Allows backward compatibility with older Premier Series. In the Off position this
switchallowsolderelectricheatboard(17P501A01)andolderECM(squareend)
compatibility.OnisforallnewerEHboard(17P514A01)andECM2(roundend).
OldEH&OldECM Normal
SW 3- 5
Ondualcapacityunitsthisswitchallowsstagechange:ontheywhenoff,and1
minute delay when on. A delay is required on all reciprocating dual capacity units.
Envision E-Series or Premier
FIELD SELECTION DIP SWITCHES (SW2)
DIP
SWITCH
NUMBER
DESCRIPTION OFF POSITION ON POSITION
SW 2- 1
Service Test Mode
Onthecontrol,allowseldselectionof“NORMAL”or“TEST”operationalmodes.
Testmodeacceleratesmosttimingfunctions16timestoallowfastertroubleshooting.
Test mode also allows viewing the “CURRENT” status of the fault inputs on the LED
display.
Test Mode Normal Speed Operation
SW 2- 2
Freeze Sensing Setting
Allowseldselectionoffreezethermistorfaultsensingtemperaturesforwellwater
(30°F)orantifreeze-protected(15°F)earthloops.
Loop Water Freeze
Protection15°F
Well Water Freeze Protec-
tion30°F
SW 2- 3
Accessory Relay
Allowseldselectionoftheaccessoryrelaytooperatewiththecompressororfan.
Acc Relay Tracks Fan
Acc Relay Tracks Compres-
sor
SW 2- 4
Fan Speed Control
Allowseldselectionofreducedfanspeed(85%ofselectedmediumandhighspeed
–ECMonly)forcoolinginthedehumidicationmode.
DehumidicationFan
Speeds
Normal Fan Speeds
SW 2- 5
Auxiliary Off
Disables 3rd-stage Heating. Full emergency heat would still be available if needed.
Disable Heating
Stage 3
Enable Heating
Stage 3
SW 2- 6
Diagnostics Inputs
AllowsviewingtheinputsfromthethermostattothecontrolboardsuchasY1,Y2,O,
G,W,SL1-InontheLEDdisplay.
Diagnostic Inputs
Viewed at LEDs
Normal Display Viewed at
LEDs
SW 2- 7
Diagnostics Outputs
Allows viewing the outputs from the control board such as compressor, reversing
valve, blower, hot water pump, and loop pump on the LED display.
Diagnostic Outputs
Viewed at LEDs
Normal Display Viewed at
LEDs
SW 2- 8
Thermostat Selection
Conguresthecontrolforapulsedlockoutsignal(ComforTalkandFaultFlashther-
mostats)orcontinuous5VAClockoutsignal.
Pulsed “L” signal Continuous “L” signal
Microprocessor Control (cont.)
NEW
]
NEW
]

Envision R-410A Specifications

General

Brand	Envision
Model	R-410A
Category	Heat Pump
Language	English