Epson LQ-2180 - Paper Loading and Path Settings

LQ-2180 Revision A
Appendix EEPROM Address Map 47
7.1 EEPROM Address Map
This chapter provides EEPROM Address Map for LQ-2180 and
component layouts and circuit diagram for the C272 Main Board.
NOTE:The data of two or more bytes are assigned in such was as
lower byte to lower address, higher byte to higher address.
Table 7-1. EEPROM Address Map (1/7)
Table 7-2. EEPROM Address Map (2/7)
Address Data Data Format
Q-pit
data
Factory
setting
00H, 01H (reserved) 0000H 0000H
Area 1
02H, 03H Character
table
selection
0: PC437
1: PC850
2: PC860
3: PC863
4: PC865
5: PC861
6: BRASCII
7: Abicomp
8: ISO Latin 1
9: Roman 8
10:PC437 Greek
11:PC852
12:PC853
13:PC855
14:PC857
15:PC864
16:PC866
17:PC869
18:ISO Latin 1T
19:ISO 8859-7
20:MAZOWIA
21:Code MJK
22:Bulgaria
23:Estonia
24:PC774
25:ISO 8859-2
26:PC866 LAT
27:PC866 UKR
28:Hebrew 7
29:Hebrew 8
30:PC862
31:PCAPTEC
32:PC708
33:PC720
34:PCAR864
35:PC858
36:ISO 8859-15
0000H 0000H
(PC437)
37:Italic U.S.A.
38:Italic France
39:Italic Germany I
40:Italic U.K.
41:Italic Denmark
42:Italic Sweden
43:Italic Italy
44:Italic Spain
0000H 0000H
Address Data Data Format
Q-pit
data
Factory
setting
04H, 05H Page length for rear
tractor
1 to 22x360 (by 1/360 inch)
0000H: 11 inch (the default)
0000H
(11 inch)
0000H
(11 inch)
06H, 07H Page length for front
tractor
1 to 22x360 (by 1/360 inch)
0000H: 11 inch (the default)
0000H
(11 inch)
0000H
(11 inch)
08H, 09H Page length for CSF
bin 1
1 to 22x360 (by 1/360 inch)
0000H: 22 inch (the default)
0000H
(22 inch)
0000H
(22 inch)
0AH, 0BH Page length for CSF
bin 2
1 to 22x360 (by 1/360 inch)
0000H: 22 inch (the default)
0000H
(22 inch)
0000H
(22 inch)
0CH, 0DH TOF adjustment
value for rear tractor
-60 to 360 (4.2 mm to 8.5
mm + 1 inch, by 1/360 inch)
0000H
(8.5 mm)
0000H
(8.5 mm)
0EH, 0FH TOF adjustment
value for front tractor
-60 to 360 (4.2 mm to 8.5
mm + 1 inch, by 1/360 inch)
0000H
(8.5 mm)
0000H
(8.5 mm)
10H, 11H TOF adjustment
value for CSF bin 1
-60 to 360 (4.2 mm to 8.5
mm + 1 inch, by 1/360 inch)
0000H
(8.5 mm)
0000H
(8.5 mm)
12H, 13H TOF adjustment
value for CSF bin 2
-60 to 360 (4.2 mm to 8.5
mm + 1 inch, by 1/360 inch)
0000H
(8.5 mm)
0000H
(8.5 mm)
14H, 15H TOF adjustment
value for rear manual
insertion
-60 to 360 (4.2 mm to 8.5
mm + 1 inch, by 1/360 inch)
0000H
(8.5 mm)
0000H
(8.5 mm)
16H, 17H TOF adjustment
value for front
manual insertion
-60 to 360 (4.2 mm to 8.5
mm + 1 inch, by 1/360 inch)
0000H
(8.5 mm)
0000H
(8.5 mm)
18H, 19H Bottom margin for
rear tractor
1 to 22x360 (by 1/360 inch),
0000H: 11inch (the default)
0000H
(11 inch)
0000H
(11 inch)
1AH, 1BH Bottom margin for
front tractor
1 to 22x360 (by 1/360 inch),
0000H: 11inch (the default)
0000H
(11 inch)
0000H
(11 inch)
1CH Font selection
0: Roman
1: Draft
2: Sans serif
3: Courier
4: Prestige
5: Script
6: Others
(the default)
00H
(Roman)
00H
(Roman)
http://www.4008109977.com guangzhou epson service :020-84207330