ESAB Rogue ES 180i Pro Service Manual

ESAB Rogue ES 180i Pro

64 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Service manual

0463 714 001 GB 20231117

Valid for: Serial No. HA017-, HA018-, HA019-, HA020-, HA026-,

HA027-, HA042-xxxx-xxxx

ES 130i Pro, ES150i, ES180i,

ES180iPro,ES200iPro,

ET180i, ET 200iP, ET 200iP Pro

Table of Contents

Other manuals for ESAB Rogue ES 180i Pro

Instruction Manual30 pages

Questions and Answers:

D
Dennis CoffeyAug 2, 2025
How to troubleshoot MMA welding problems with my ESAB Rogue ES 180i Pro Welding System?
- K
  Kimberly HernandezAug 2, 2025
  If you're experiencing issues with MMA welding on your ESAB Welding System, make sure that the welding process is set for MMA. Also, verify that the welding and return cables are correctly connected to the power source. Ensure the return clamp has good contact with the workpiece. Check that you're using the correct electrodes and polarity (refer to the electrode packaging for polarity). Confirm the correct welding current (A) is set, and adjust Arc Force and Hot start as needed.
P
Patricia HarrisAug 6, 2025
How to fix TIG welding problems on my ESAB Rogue ES 180i Pro?
- A
  amandasalinasAug 6, 2025
  If you're having TIG welding problems with your ESAB Welding System, ensure the welding process is set for Live TIG as necessary. Confirm that the TIG torch and return cables are correctly connected to the power source. Ensure the return clamp has good contact with the workpiece and that the TIG torch lead is connected to the negative welding terminal. Also, be sure you're using the correct shielding gas, gas flow, welding current, filler rod placement, electrode diameter, and welding mode on the power source. Finally, check that the gas valve on the TIG torch is ON.
K
Kayla RodriguezAug 10, 2025
What to do if my ESAB Welding System has no arc?
- L
  Lauren OlsonAug 10, 2025
  If your ESAB Welding System has no arc, start by checking that the electrical power supply switch is turned on and that the display is on, verifying the power source has power. Also, check that the setting panel displays correct values. Ensure the welding and return cables are correctly connected and inspect the electrical power supply fuses.
S
Stephen GrimesAug 15, 2025
How to troubleshoot Live TIG (GTAW) welding problems with my ESAB Welding System?
- L
  Lisa AlvarezAug 15, 2025
  If you're experiencing issues with Live TIG (GTAW) welding on your ESAB Welding System, ensure the welding process is correctly set for Live TIG. Verify that both the TIG torch and return cables are properly connected to the power source, and the return clamp has good contact with the workpiece. Confirm the TIG torch lead is connected to the negative welding terminal. Check that you are using the correct shielding gas, gas flow, welding current, filler rod placement, electrode diameter, and welding mode on the power source. Finally, ensure the gas valve on the TIG torch is turned ON.
M
Michael GeorgeAug 25, 2025
Why does the thermal protection trip frequently on my ESAB Rogue ES 180i Pro Welding System?
- A
  Amber JacksonAug 25, 2025
  If the thermal protection on your ESAB Welding System trips frequently, ensure that you have not exceeded the recommended duty cycle for the weld current, referring to the "Duty cycle" section in "TECHNICAL DATA". Also, verify that the air inlets or outlets are not clogged. Clean the inside of the machine using routine maintenance methods.
A
Abigail MooreAug 28, 2025
What to do if welding current is interrupted during welding with my ESAB Welding System?
- L
  Laura LawrenceAug 28, 2025
  If the welding current is interrupted during welding with your ESAB Welding System, check whether the Over Temperature LED (Thermal Protection) on the setting panel is illuminated. Then, continue troubleshooting as if there is "No Arc."
D
David WagnerSep 10, 2025
How to solve Stick (SMAW) welding problems on my ESAB Welding System?
- N
  Nathan MontgomerySep 12, 2025
  To troubleshoot Stick (SMAW) welding issues on your ESAB Welding System, first, check that the welding process is set for Stick (SMAW). Then, confirm that the welding and return cables are correctly connected to the power source and that the return clamp has good contact with the workpiece. Verify that you are using the correct electrodes and polarity (check the electrode packaging for polarity). Ensure that the correct welding current is set. Adjust the Arc Force and Hot start settings as needed.

ESAB Rogue ES 180i Pro Specifications

General

Brand	ESAB
Model	Rogue ES 180i Pro
Category	Welding System
Language	English

Related product manuals

Preview: ESAB MiniArc Rogue ES 180i

ESAB MiniArc Rogue ES 180i

ESAB Rogue ES 150i

Preview: ESAB Rogue ES 130i PRO

ESAB Rogue ES 130i PRO

ESAB Rogue ES 200i Pro

Preview: ESAB ES 180i

Preview: ESAB ES 180i PRO

ESAB ES 180i PRO

ESAB Rogue EM 180

Preview: ESAB Rogue ET 200iP

ESAB Rogue ET 200iP

Preview: ESAB Rogue ET 230iP

ESAB Rogue ET 230iP

Preview: ESAB Rogue EMP 210 PRO

ESAB Rogue EMP 210 PRO

Preview: ESAB Rogue Series

ESAB Rogue Series

Preview: ESAB Ruffian ES 150G EDW

ESAB Ruffian ES 150G EDW