Everbilt EFLS15-HD - User Manual

Questions and Answers

C
Calvin WilsonAug 10, 2025
What to do if my Everbilt EFLS15-HD Water Pump does not deliver water to full capacity?
- C
  caseyjulieAug 10, 2025
  If your Everbilt Water Pump isn't delivering water to its full capacity, it could be due to several reasons. If the water level in the well is lower than estimated, a deep well jet may be needed if the depth to water exceeds 25 ft. Corroded or limed steel piping can cause excess friction; replace it with plastic pipe where possible, or with new steel pipe. Insufficient piping size can also restrict water flow, so use larger piping. Finally, the pump might not be receiving enough water, in which case you should add additional well points.
A
Austin MontesAug 15, 2025
What to do if my Everbilt EFLS15-HD Water Pump motor will not run?
- R
  Richard HerreraAug 15, 2025
  If your Everbilt Water Pump motor isn't running, there are several potential causes. First, check if the disconnect switch is turned on. Next, inspect the fuse to see if it's blown or the circuit breaker has tripped; replace the fuse or reset the breaker if needed. A defective pressure switch could also be the culprit, in which case you should disconnect the power and replace the switch. Finally, examine the wiring at the motor to ensure it's correctly wired and all connections are secure, referring to the wiring instructions and disconnecting power before checking.
Z
zwrightAug 27, 2025
What to do if my Everbilt EFLS15-HD Water Pump motor runs hot and overload kicks off?
- G
  Gregory FullerAug 27, 2025
  If your Everbilt Water Pump motor runs hot and the overload kicks off, or if the motor only hums and doesn't run, it could be due to incorrect wiring. Refer to the wiring instructions to ensure it is properly connected. Another cause might be low voltage. Check with the power company and consider installing heavier wiring if the current wiring is too small, referring to the wiring chart.
S
Stephen GarrettSep 2, 2025
What to do if my Everbilt EFLS15-HD leaks around the clamp?
- W
  William HawkinsSep 2, 2025
  If your Everbilt Water Pump is leaking around the clamp, the clamp may be loose. Stop the pump and tighten the clamp nut by 1-2 turns. Alternately tighten and tap on the clamp with a mallet to seat the O-ring, being careful not to overtighten.
A
Adrian MosesNov 20, 2025
Why does my Everbilt EFLS15-HD motor run but no water is delivered?
- J
  Justin BuckNov 20, 2025
  If your Everbilt Water Pump motor runs but no water is delivered, several issues could be the cause. Ensure the pump was primed correctly according to the instructions. Check for air leaks in all connections on the suction line, shaft seal, and AVC, using shaving cream to identify leaks. A leaking foot valve or check valve may also be the problem, requiring replacement. Additionally, verify that the pipe size matches the suction and discharge ports on the pump. If the water level is below the suction pipe inlet, lower the suction line into the water and re-prime; a deep well pump may be necessary if the water level exceeds 25 ft. A plugged impeller can also prevent water delivery, so clean it. If the check valve or foot valve is stuck shut, replace it. Frozen pipes can also block water flo...

Summary

Safety Information

Important Safety Instructions

Essential safety guidelines and symbol definitions for pump operation.

Warranty

Pre-installation

Materials Required

List of necessary materials not included with the pump for installation.

Installation

Well Pipe Installation

Covers installation methods for cased/dug and driven point wells.

Surface Water Installation

Guidelines for vertical or horizontal installation from surface water sources.

Lawn Sprinkling Application

Specific setup for using the pump in lawn irrigation systems.

Pump;Piping Installation

General instructions for pump and piping setup and connections.

Electrical Settings

Operation

Priming the Pump

Step-by-step guide to prime the pump before operation.

Care and Cleaning

Maintenance

Winterization

Troubleshooting

Service Parts

Everbilt EFLS15-HD Specifications

General

Model	EFLS15-HD
Category	Water Pump
Voltage	115 V
Maximum Flow Rate	1800 GPH
Maximum Lift Height	25 ft
Power Cord Length	10 ft
Material	Thermoplastic
Type	Submersible
Horsepower	0.15 HP
Discharge Size	1-1/4 in NPT
Outlet size	1-1/4 in NPT