Everbilt EFLS15CI-HD - User Manual

Questions and Answers

T
twatsonAug 1, 2025
Why Everbilt EFLS15CI-HD Water Pump does not deliver water to full capacity?
- J
  James ThomasAug 2, 2025
  If your Everbilt Water Pump isn't delivering water to its full capacity, it could be due to several reasons: * If your well's water level is lower than estimated, a deep well jet may be needed if the depth to water is more than 25 ft. (7.6M). * Corroded or limed steel piping can cause excess friction; replace it with plastic pipe where possible, or with new steel pipe. * Ensure you are using larger piping. * You might need to add additional well points if the pump isn't being supplied with enough water.
W
William WuAug 7, 2025
What to do if Everbilt EFLS15CI-HD Water Pump leaks around the clamp?
- R
  Renee KellyAug 7, 2025
  If your Everbilt Water Pump is leaking around the clamp, stop the pump and tighten the clamp nut 1-2 turns. Alternately tighten and tap on the clamp with a mallet to seat the O-ring. Be careful not to overtighten.
K
Katherine French MDAug 13, 2025
What to do if Everbilt EFLS15CI-HD motor will not run?
- T
  tsmithAug 13, 2025
  If your Everbilt Water Pump motor isn't running, here are a few things to check: * Ensure the disconnect switch is on. * Replace the fuse or reset the circuit breaker if it has blown or tripped. * If the starting switch is defective, disconnect the power and replace it. * Also, disconnect the power and check all wiring, referring to the wiring instructions to ensure they are tight and correctly connected.
M
Marissa CunninghamAug 26, 2025
Why does my Everbilt Water Pump motor run hot and overload kicks off or the motor does not run and only hums?
- M
  Mrs. Lisa WilliamsAug 26, 2025
  If your Everbilt Water Pump motor runs hot and the overload kicks off, or if it only hums and doesn't run, it could be due to incorrect wiring. Refer to the wiring instructions to ensure it is correctly wired. Also, low voltage could be the cause. Check with the power company and consider installing heavier wiring if the wire size is too small, referring to the chart in the wiring section.
C
Caroline SmithNov 18, 2025
What to do if Everbilt Water Pump motor runs but no water is delivered?
- G
  gonzalezkathleenNov 18, 2025
  If the Everbilt Water Pump motor runs, but no water is delivered, consider the following: * Re-prime the pump according to the instructions. * Check all connections on the suction line, shaft seal, and AVC for air leaks using shaving cream. * Replace the foot valve or check valve if they are leaking or stuck shut. * Ensure the pipe size matches the suction and discharge ports on the pump. * Lower the suction line into the water and re-prime if the water level is below the suction pipe inlet. Note that if the receding water level in the well exceeds 25 ft. (7.6M), a deep well pump is needed. * Clean the impeller if it's plugged. * Thaw pipes if they are frozen, and consider burying them below the frost line or heating the pit or pump house. * Raise the foot valve and/or str...

Summary

Safety Information

IMPORTANT SAFETY INSTRUCTIONS

Crucial instructions for safe operation, installation, and maintenance, including safety symbols.

Warranty

Pre-installation

MATERIALS REQUIRED (NOT INCLUDED)

Lists essential materials and components needed before starting pump installation and operation.

Installation

CASED WELL;DUG WELL INSTALLATION

Detailed steps for installing the pump in cased or dug wells, including foot valve placement and well seals.

DRIVEN POINT INSTALLATION

PUMP;PIPING INSTALLATION

PIPE FROM WELL TO PUMP

Electrical Settings

MOTOR SWITCH SETTINGS

Instructions for setting the motor to the correct voltage (115V or 230V) for the power supply.

Wiring Connections

Operation

PRIMING THE PUMP

Step-by-step guide on how to prime the pump, expelling air and establishing water flow from the source.

Care and Cleaning

Clearing a Clogged Pump

Procedure for disassembling, cleaning debris, and reassembling the pump to resolve clogging issues.

Troubleshooting

Service Parts

Everbilt EFLS15CI-HD Specifications

General

Model	EFLS15CI-HD
Category	Water Pump
Type	Submersible Utility Pump
Max Head	25 ft
Power Cord Length	10 ft
Weight	7.5 lbs
Material	Thermoplastic
Voltage	115V
Discharge Size	1-1/2 in