Extron electronics DTP CrossPoint 4K Series - Setup and Installation Checklist

10 DTP CrossPoint 4K Series • Installation
Q
LAN (Ethernet) port (non-IPCP model) — If desired,
LAN
connect a network WAN or LAN hub, a control system,
or a computer to the Ethernet RJ-45 port (see TP
connectors on page 12 to wire the connector).
NOTE: The factory default IP address is 192.168.254.254.
R
IPCP control processor (IPCP models) — The IPCP models
include a built-in control processor that can control and monitor
a variety of external devices. The IPCP offers RS-232 and
IR-based control, relays, and digital I/O controls. See the IPCP
Pro Series Setup Guide, included with the switcher, to make
all connections and to configure and operate the IPCP control
processor.
S
Remote port — Plug a serial RS-232 device into the
Tx Rx G
REMOTE
matrix switcher via this 3.5 mm, 3-pole captive screw
connector for remote control of the switcher (see
RS-232 and IR connectors on page 15 to wire the
connector).
Switcher Reset
50-60 Hz
100-240V ~
--A MAX
RESET
DTP CROSSPOINT 108 4K
Tx Rx RTSCTS GTxRxG Tx Rx G
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
LAN 2
LAN 1
LAN 3
R
AUDIO OUTPUTS
AMP OUTPUT
CONTROL
1234G
DIGITAL I/OCOM 3COM 2
AUDIO INPUTS
COM 1
S
DMP EXPANSION
SGG
1
1
2
2
C34C
-S G+S+V
PWR OUT = 6W
1
LR
1
LR
3
L R
3
LR
5
LR
2
LR
4
L R
2
LR
4
LR
6
LR
IR/SERIAL eBUSRELAYS
1
CLASS 2 WIRING
70V
1 2 3 4 5A 6A
XTP
DTP
HDBT
OUTPUTS
SIG LINK
OUT
5B 6B 6
XTP
S/PDIF
OUT
DTP
HDBT
Tx
XTP
DTP
HDBT
78
XTP
DTP
HDBT
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
OUT
XTP
DTP
XTP
DTP
123457 86
INPUTS INPUTS
XTP
DTP
XTP
DTP
91
0
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
Tx Rx G
REMOTE
LAN
T
Figure 10. Reset button and LED
50-60 Hz
100-240V ~ -- A MAX
+48V
MIC/LINE
1
1
3
2
4
2
3
4
EXP
DTP CROSSPOINT 84 4K
AUDIO OUTPUT
S
AUDIO INPUTS
DMP EXPANSION
1
LR
1
R
3
LR
3
LLR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
AMP OUTPUT
CLASS 2 WIRING
1
100V
12
1 23456
3A 4A
4B
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx Rx
XTP
DTP
XTP
DTP
XTP
DTP
XTP
DTP
HDBT
HDBT
G
7
8
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
INPUTS
OUTPUTS
3B
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
4
S/PDIF
OUT
R
CONTROL
Tx Rx RTSCTS G
12
12
SGSG
C
34C+V
PWR OUT = 6W
+V D-S+S
Tx Rx G Tx Rx G1234G
COM 1 COM 3COM 2 DIGITAL I/O
LAN 1
LAN 2 LAN 3
IR/SERIAL RELAYS DIGITAL I/O
Tx Rx G
REMOTE
RESET
T
Figure 11. Reset button and LED
T
Switcher Reset button and LED — Initiates four levels of
matrix switcher reset. For different reset levels, press and hold
the recessed Reset button while the switcher is running or
while you power up the switcher.
See the DTP CrossPoint 4K Series User Guide, at
www.extron.com.