1
ENGLISH
WARNINGS
• Important! For the safety of people, it is important that all the instructions be carefully observed.
• Incorrect installation or incorrect use of the product could cause serious harm to people.
• Carefully read the instructions before beginning to install the product and keep them for future reference.
•
The symbol indicates notes that are important for the safety of persons and for the good condition of the automated system.
• The symbol draws your attention to the notes on the characteristics and operation of the product.
INDEX
1 LAY-OUT OF ELECTRICAL BOX ........................................................................................ 2
2 WARNINGS ................................................................................................................... 4
3 LAYOUT AND COMPONENTS OF E124 ........................................................................... 4
3.1 INPUTS DEFAULT SETTING
............................................................................................ 4
3.2 DESCRIPTION OF COMPONENTS ...............................................................................
5
4 TECHNICAL SPECIFICATIONS ......................................................................................... 5
5 TERMINAL BOARDS, CONNECTORS, INPUTS AND SIGNALS ............................................ 6
5.1 TERMINAL BOARD J3 – CONNECTION TO BUS-2EASY ACCESSORIES ........................ 6
5.2 TERMINAL BOARD J4 – SIGNALS INPUTS .................................................................... 6
5.3 TERMINAL BOARDS J5, J8 – OUT1 AND OUT2 ............................................................ 6
5.4 TERMINAL BOARD J6 – OPENING AND CLOSING TRAVEL LIMIT DEVICE ...................... 7
5.5 TERMINAL BOARDS J7 - ENCODERS .......................................................................... 7
5.6 TERMINAL BOARD J9 – FLASHING LAMP .................................................................... 7
5.7 TERMINAL BOARD J10 – ELECTRIC LOCK ................................................................... 7
5.8 TERMINAL BOARD J11, J12 - MOTORS ...................................................................... 7
5.9 CONNECTOR J1 - PRIMARY POWER FEED FROM 230/115 V MAINS .......................... 7
5.10 CONNECTOR J2 - SECONDARY POWER FEED ............................................................ 8
5.11 Connector J13 – XF MODULE rapid connection ...................................................... 8
5.12 CONNECTOR J14- FOR RAPID CONNECTION OF MINIDEC, DECODER AND RP ......... 8
5.13 Connector M1A – Rapid connection MODULE X-COM ............................................ 8
6 ELECTRICAL CONNECTIONS .......................................................................................... 9
6.1 TRADITIONAL PHOTOCELLS ........................................................................................ 9
6.2 PHOTOCELLS BUS-2EASY ........................................................................................... 11
6.2.1 ADDRESSING THE BUS-2EASY PHOTOCELLS ........................................................
11
6.2.2 MEMORY STORAGE OF BUS-2EASY ACCESSORIES ...............................................
12
6.2.3 ADDRESSING THE BUS-2EASY ENCODERS ............................................................
12
7. PROGRAMMING ............................................................................................................ 13
7.1. 1
ST
LEVEL PROGRAMMING ........................................................................................ 13
7.2. 2
nd
LEVEL PROGRAMMING ....................................................................................... 16
7.3. PROGRAMMING FROM PC (3
rd
LEVEL) ....................................................................... 22
8 SAVING THE RADIO CODE .............................................................................................
22
8.1 SAVING DS RADIO CONTROLS ..................................................................................
22
8.2 SAVING SLH RADIO CONTROLS .................................................................................
22
8.3 MEMORY STORAGE OF THE LC/RC RADIO CONTROLS (FOR SOME MARKETS ONLY) ..
23
8.3.1 REMOTE SAVING OF LC/RC RADIO CONTROLS ....................................................
23
8.4 RADIO CONTROLS DELETION PROCEDURE ...............................................................
23
9 CONNECTION TO EMERGENCY BATTERIES (OPTIONAL) .................................................
23
10 START-UP
....................................................................................................................... 24
10.1 LEDS CHECK .............................................................................................................
24
10.2 TIME LEARNING - SETUP .............................................................................................
25
11 AUTOMATED SYSTEM TEST .............................................................................................
25
12 ALARM AND ERROR SIGNALS ........................................................................................
25
12.1 ALARMS ....................................................................................................................
25
12.2 ERRORS ....................................................................................................................
25
13 FUNCTION LOGICS ........................................................................................................
26
CE DECLARATION OF CONFORMITY
Manufacturer: FAAC S.p.A.
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
Declares that: The E124 control unit
• ·conforms to the essential safety requirements of the following EEC directives
2006/95/EC Low Voltage Directive
2004/108/EC Electromagnetic Compatibility Directive
Additional note:
This product underwent tests in a typical uniform configuration
(all products manufactured by FAAC S.p.A.).
Bologna, 01 - 01 - 2010
The Managing Director
A.Marcellan
To Next Page
Loading...
