Faema E92 Elite - Page 38

Once you have selected AUTOSTEAM, use the “+” (34) and “-” (35)
keys to position the cursor on the T STOP STEAM line, and press
the PROG (32) key.
You may now program the automatic steam function, by setting a
“xxx°C” temperature value for either hot or whipped milk.
Setting options:
"0" setting:
  PDQXDOVWHDPVWRS
Any number between "40°C ÷ 85°C" (104°F ÷ 185°F)
  DXWRPDWLFVWHDPVWRS
"OFF" setting:
  VWHDPVWRSGLVDEOHG
Use the “+” (34) and “-” (35) keys also to modify the message or
number.
When the key (33) is pressed, the following message is again
displayed:
7KH RWKHU $XWRVWHDP VHOHFWLRQ SDUDPHWHUV WKDW FDQ EH PRGL¿HG
are:
- regolator - YES/ NO.
- emulsion level - ·WKHPDFKLQHGRHVQRWKDYHWKHÀRZ
regolator)
Autosteam can be programmed in two ways:
FIRST WAY: AUTOMATIC STEAM STOP
Set the temperature at the entry "T stop steam xxx°C" using the "+"
and (34) and the "-" (35) keys, with "xxx" set between 40º and 85ºC.
Steam is dispensed when the key (12) is pressed, and the lever (11)
is pressed for the type of milk.
In particular:
- lever down: foamed milk
- lever up: heated milk.
After pressing the key (12), the temperature detected by the probe
appears on the display.
N.B.: When the set temperature is reached, steam supply stops
automaticallyDQGWKHGLVSOD\FRQWLQXHVLQGLFDWLQJVWHDPYDOXHIRU
WKHQH[WPLQXWHV
6WHDPFDQEHVWRSSHGDWDQ\WLPHHYHQLIWKHVHWWHPSHUDWXUHKDVQRW
EHHQUHDFKHGE\SUHVVLQJWKHDXWRPDWLFVWHDPNH\DJDLQ12).
02'(67($00$18$/6723
Set the temperature value on item "T stop steam xxx°C" at "000"
zero.
Steam dispensing and the choice of milk type are performed as in
MODE 1
Press the key (12) to dispense steam.
Immediately the message "T stop steam xxx°C" appears on the display,
indicating the temperature read by the probe.
NRWH7KHXVHUFRQWUROVZKHQVWHDPGLVSHQVLQJLVVWRSSHG:KHQWKH
GHVLUHGWHPSHUDWXUHLVUHDFKHGWKHXVHUZLOOSXVKRQNH\12).
)RUWKHQH[WDIWHUVWHDPGLVSHQVLQJKDVVWRSSHGWKHGLVSOD\VKRZV
WKHPLONWHPSHUDWXUHWKDWKDVEHHQUHDFKHG
 7HFKQLFLDQSURJUDPPLQJ&RQ¿JXUDWLRQPHQX$XWRVWHDP (Turbosteam)
ÀTURBOSTEAM
T stop steam 081°C
+
Time out is set at 180" for both the programming modes.
If, when the machine is powered up, the probe does not detect any
temperature value (thermo-couple not operating), the STOP STEAM
function is disabled and "----" is shown in the setting square instead
of "xx°C". The latest set temperature value is, however, saved until
thermo-couple operation is restored.
The machine works as if the STOP STEAM function does not exist.
Frothed milk and hot milk are available, but the temperature read by
the probe will not appear on the display.
(Where is present)
The ideal setting for milk frothing is set in the factory. If additional
DGMXVWPHQWVPXVWEHPDGHWXUQWKHÀRZDGMXVWPHQWYDOYH$XQGHU
the basin on the right hand side of the machine:
- counterclockwise: more air > more frothy milk
- clockwise: less air > less frothy milk
Note: even slight turns of the valve (A) can make a great difference
in how the milk is frothed.
A
9
12
11
9
12
11
Hot milkFrothed milk
ÀTURBOSTEAM
T stop steam 081°C
+
Æ
75
English