What to do if my FBD 774 Beverage Dispenser displays 'Board Failure'?
If your FBD Beverage Dispenser is showing a 'Board Failure', cycle the power to the unit to see if it will clear the error. If not, replace the control board, because the control board may not be functioning properly.
What to do if the FBD Beverage Dispenser shows 'Syrup Out' error #011, 012, 013, 014?
If the FBD Beverage Dispenser displays a 'Syrup Out' error, it indicates that the syrup pressure is less than 45 PSIG (310 kPag), especially for the base syrup in multi-flavor dispensers. Here's what you should do: * Replace the empty BIB (Bag-In-Box). * Ensure the gas line is properly connected to the BIB pump. * Check that the BIB pump is operating correctly. * Make sure the gas tank is not empty. * Verify the syrup shutoff valve at the solution module is turned on. * Confirm that any syrup shutoff valves at the back of the dispenser are not turned off. * Ensure the syrup supply pressure at the dispenser reads 70 PSIG (483 kPag), adjusting the regulator if necessary. * Check that the syrup pressure transducer is connected and working properly.
Why does my FBD Beverage Dispenser say 'Compressor Ran Too Long'?
If your FBD Beverage Dispenser shows 'Compressor Ran Too Long', and the location is an extreme volume venue such as a festival, contact FBD service for instructions on adjusting the timer. Otherwise, run the refrigeration diagnostic sequence to determine the reason for the failure, because the compressor may have run continuously for more than 90 minutes.
What does error #450: Gas #1 - High Regulated CO2 PSI mean on my FBD Beverage Dispenser and how to resolve it?
Error #450 'Gas #1 - High Regulated CO2 PSI' on your FBD Beverage Dispenser indicates that the regulated CO2 pressure is above 70 PSIG (483 kPag). Check the 'Gas 1' regulator on the header tray and ensure it is set to 60 PSIG (414 kPag).
What does error #030: Water Out mean on my FBD Beverage Dispenser and how to fix it?
Error #030 'Water Out' on your FBD Beverage Dispenser indicates that the water pressure is less than 45 PSIG (310 kPag). Here’s how to troubleshoot: * Ensure the water line to the dispenser is on and the water shutoff at the solution module is turned on. * Check that the gas supply line is connected to the water pump and the pump is not stalled. * Verify the gas supply pressure at the dispenser is reading 70 PSIG (483 kPag). Adjust the regulator if needed. * Confirm the water pressure transducer is connected and working properly.
What does error #480: Gas #2 - Low Regulated CO2 PSI mean on my FBD Beverage Dispenser and how to fix it?
Error #480 'Gas #2 - Low Regulated CO2 PSI' on your FBD Beverage Dispenser means that the regulated CO2 pressure dropped below 50 PSIG (345 kPag). To fix it: * Ensure the CO2 supply is not low. * Check the 'Gas 2' regulator on the header tray and ensure it is set to 60 PSIG (414 kPag).
What does error #200: Return Temperature Sensor mean on my FBD Beverage Dispenser and how do I fix it?
Error #200 'Return Temperature Sensor' on your FBD Beverage Dispenser indicates that the refrigeration return (suction) temperature sensor is not reading correctly. To fix it: * Ensure the temperature sensor is plugged in. * Replace the sensor if faulty.
What does 'MOTOR FAILURE' mean on my FBD Beverage Dispenser and how can I fix it?
The 'MOTOR FAILURE' message on your FBD Beverage Dispenser indicates that a beater motor is stalled. Run the beater circuit diagnostic sequence to troubleshoot this issue.
How to resolve 'High Barrel Pressure' on FBD Beverage Dispenser?
To troubleshoot a 'High Barrel Pressure' error on your FBD Beverage Dispenser, dispense a drink to reduce the barrel pressure. If set to the ON mode, the unit will refreeze. Run the fill diagnostic if a failed component is suspected. Check the “Active Charge” regulator located on the product header to ensure it is set at 30 PSI. Make sure all barrels should be fully depressurized before checking the active charge, because pressure on a barrel may have exceeded 55 PSI.
What to do if my FBD Beverage Dispenser says 'Water Out'?
To fix a 'Water Out' error on your FBD Beverage Dispenser, make sure the water line to the unit is on and the water shutoff at the solution module is turned on. Ensure the CO2 supply line is connected to the water pump and that the pump is not stalled. Verify the CO2 supply pressure at the dispenser is reading 70 PSI, adjusting the regulator if needed. Also, check that the water pressure transducer is connected and working properly, because water pressure may be less than 45 PSI.
Guidelines for proper electrical grounding and shock prevention for dispenser operation.
Precautions for handling compressed gases to prevent injury or death from leaks.
Instructions for connecting the dispenser to the electrical power supply, including plug types and voltage.
Steps for checking for leaks and priming the system before initial operation.
Procedure for the first power-up, including language, barrel count, and pressure verification.
Steps for purging air, filling barrels with product, and initiating the freezing cycle.
Configuring remote monitoring system and modem settings for network connectivity.
Resetting dispenser settings to default and running diagnostic sequences for troubleshooting.
Guidelines for maintaining dispenser cleanliness and sanitation to ensure proper operation.
Steps for sanitizing the dispenser annually or after periods of non-operation for hygiene.
Procedure for replacing motor rear seals annually to prevent leaks and potential motor failures.
Explanation of error codes, their meanings, and recommended troubleshooting steps for diagnosis.
General| Brand | FBD |
|---|---|
| Model | 774 |
| Category | Beverage Dispenser |
| Language | English |
To Next Page
