What to do if my FBD 774 Beverage Dispenser displays 'Board Failure'?
If your FBD Beverage Dispenser is showing a 'Board Failure', cycle the power to the unit to see if it will clear the error. If not, replace the control board, because the control board may not be functioning properly.
How to diagnose 'Motor Failure' in FBD Beverage Dispenser?
To resolve a 'Motor Failure' on your FBD Beverage Dispenser, run a beater circuit diagnostic to determine the problem or refer to error #58X in this manual. Check to make sure the beater motor is plugged in, because the beater motor may not be operating.
Why does my FBD Beverage Dispenser say 'Compressor Ran Too Long'?
If your FBD Beverage Dispenser shows 'Compressor Ran Too Long', and the location is an extreme volume venue such as a festival, contact FBD service for instructions on adjusting the timer. Otherwise, run the refrigeration diagnostic sequence to determine the reason for the failure, because the compressor may have run continuously for more than 90 minutes.
What to do if my FBD Beverage Dispenser displays Error #111, 112, 113, 114: Motor Failure?
If your FBD Beverage Dispenser displays Error #111, 112, 113, 114 indicating 'Motor Failure', it means the beater motor is not operating. To solve this: * Run a beater circuit diagnostic to determine the problem or refer to error #58X in this manual. * Check to make sure the beater motor is plugged in.
What does error #200: Return Temperature Sensor mean on my FBD Beverage Dispenser and how do I fix it?
Error #200 'Return Temperature Sensor' on your FBD Beverage Dispenser indicates that the refrigeration return (suction) temperature sensor is not reading correctly. To fix it: * Ensure the temperature sensor is plugged in. * Replace the sensor if faulty.
Why does my FBD Beverage Dispenser say 'CO2 OUT'?
The FBD Beverage Dispenser displays 'CO2 OUT' when the CO2 supply is depleted. Restore the CO2 supply to resolve this. The dispenser will automatically restart.
What to do for 'High regulated CO2 PSI' on FBD Beverage Dispenser?
If your FBD Beverage Dispenser displays a 'High regulated CO2 PSI' error, check the “carbonation” regulator on the header tray and ensure it is set to 60 PSI, because regulated CO2 pressure may be above 70 PSI.
How to fix 'Low regulated CO2 PSI' on FBD 774 Beverage Dispenser?
If you encounter a 'Low regulated CO2 PSI' error on your FBD Beverage Dispenser, make sure the CO2 supply is not low. Check the “carbonation” regulator on the header tray and ensure it is set to 60 PSI, because the regulated CO2 pressure may have dropped below 50 PSI.
How to resolve 'High Barrel Pressure' on FBD Beverage Dispenser?
To troubleshoot a 'High Barrel Pressure' error on your FBD Beverage Dispenser, dispense a drink to reduce the barrel pressure. If set to the ON mode, the unit will refreeze. Run the fill diagnostic if a failed component is suspected. Check the “Active Charge” regulator located on the product header to ensure it is set at 30 PSI. Make sure all barrels should be fully depressurized before checking the active charge, because pressure on a barrel may have exceeded 55 PSI.
What to do if my FBD Beverage Dispenser says 'Water Out'?
To fix a 'Water Out' error on your FBD Beverage Dispenser, make sure the water line to the unit is on and the water shutoff at the solution module is turned on. Ensure the CO2 supply line is connected to the water pump and that the pump is not stalled. Verify the CO2 supply pressure at the dispenser is reading 70 PSI, adjusting the regulator if needed. Also, check that the water pressure transducer is connected and working properly, because water pressure may be less than 45 PSI.
Guidelines for proper electrical grounding and shock prevention for dispenser operation.
Precautions for handling compressed gases to prevent injury or death from leaks.
Instructions for connecting the dispenser to the electrical power supply, including plug types and voltage.
Steps for checking for leaks and priming the system before initial operation.
Procedure for the first power-up, including language, barrel count, and pressure verification.
Steps for purging air, filling barrels with product, and initiating the freezing cycle.
Configuring remote monitoring system and modem settings for network connectivity.
Resetting dispenser settings to default and running diagnostic sequences for troubleshooting.
Guidelines for maintaining dispenser cleanliness and sanitation to ensure proper operation.
Steps for sanitizing the dispenser annually or after periods of non-operation for hygiene.
Procedure for replacing motor rear seals annually to prevent leaks and potential motor failures.
Explanation of error codes, their meanings, and recommended troubleshooting steps for diagnosis.
General| Brand | FBD |
|---|---|
| Model | 774 |
| Category | Beverage Dispenser |
| Language | English |
To Next Page
