Fluke 8845A - Page 91

102 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Digital Multimeter

Introduction

83

Table 32. Calibration Errors (cont.)

Error Code Error Text Description

714 CAL Math Math error during calibration.

715 CAL Timeout Timeout error during calibration.

Table of Contents

Digital Multimeter1
Table of Contents3
Introduction9
Safety Information9
- Symbols10
- Local and Remote Operation10
- Computer Interfaces11
Optimizing System Speed for IO Operation11
Selecting the Remote Interface Port12
Configuring the IEEE-448 Port12
- IEEE 488 Operating Limitations12
- Setting the IEEE 488 (GPIB) Port Address12
- Capability Commands13
- Interconnections13
Configuring the RS-232 Port14
- Setting RS-232 Baud Rate14
- Setting RS-232 Parity and Data Bits15
- Setting RS-232 Stop Bits15
- Setting RS-232 Flow Control15
- Setting RS-232 End-Of-Line Character15
- Enabling and Disabling Fluke 45 Emulation Echo15
- RS-232 Modes of Operation16
- Operating with Flukeview Forms18
- Interconnections18
Configuring the Ethernet (LAN) Port19
- Setting the IP Address20
- Setting the LAN Subnet Mask21
- Reading the Domain Name21
- Configuring the Host Name21
- Reading the MAC Address22
- Configuring the LAN Default Gateway22
- Configuring the General Network Socket Port22
Establishing an Ethernet Connection23
Terminating an Ethernet Connection24
Selecting the Programming Language24
Getting Started with an Installation Test24
- Installation Test for RS-232 Connections24
- Installation Test for IEEE 488 Connections25
- If Test Fails25
How the Meter Processes Input26
- Input Strings26
- Input Terminators26
- Typical IEEE 488 Input Strings27
- Sending Numeric Values to the Meter27
- Sending Command Strings to the Meter27
How the Meter Processes Output29
Triggering Input29
- Internal Triggering29
- External Triggering30
Service Requests (IEEE 488 Only) and Status Registers30
- Standard Event Status and Standard Event Status Enable Registers31
- Questionable Data Event Register and Questionable Data Enable Register32
- Status Byte Register33
- Reading the Status Byte Register33
- Service Request Enable Register34
Supported SCPI Commands35
- SCPI Command Summary35
- SCPI Command Details44
- Using the Measure? Command45
- Using the Configure Command46
- Preset Conditions for the Measure? and Configure Commands48
- Using the READ? Command49
- Using the Initiate Command49
- Using the Fetch? Command49
- Using the Sense Subsystem to Configure the Meter49
- Programming for Math Operations58
- Programming the Trigger System62
- Using System-Related Commands65
- Using Status Reporting Commands68
- Calibration Commands70
- Using RS-232/Ethernet Interface Commands72
- Command Terminators73
- Alternate Programming Language Compatibility74
FLUKE 45 Command Emulation Summary75
- Computer Interface Command Set75
- IEEE 488 Capabilities and Common Commands75
- Triggering Output82
Using Flukeview Forms83
Introduction85
- Ethernet/Gpib Configuration Errors89
- Calibration Errors90
Introduction93
Incompatible Fluke 45 Commands93
- Dual Functions94
- Reading Rates94
- Ranges94
Introduction95
Your Meter and Your Network Administrator95
Network Primer96
- Physical Layer Wiring Schemes Supported by the Meter96
- Network Interconnection Devices97
- Basic Network Packet and Frame Contents97
- IP Addresses and Segmented Networks98
- IP Address Assignments99
- TCP/IP Protocol Stack100

Other manuals for Fluke 8845A

Manual126 pages

Calibration Manual112 pages

User Manual104 pages

Related product manuals

Preview: Fluke 8840A

Preview: Fluke 8842A

Preview: Fluke 8846A

Preview: Fluke 8846A/C

Preview: Fluke 88 V

Preview: Fluke 8808A

Preview: Fluke 83

Preview: Fluke 87V

Preview: Fluke 83V

Preview: Fluke 867B

Preview: Fluke 8508A