Fly Sky FS-GT3 User Manual

MODELS FS GT3
9
Digital propotional radio control sytem
Http www flysky cn com
1 0 2 4G Op er a ti o n no te s
Match line
ߖౕᄏ
Figure 1
Bind key
10 01 Matching (code
AInstall the battery to 2.4G transmitter and shut it down.
B 1˅DŽInsert the matching lines to the channel BIND CH3 port of the receiver. Figure.
CConnect the receiver battery to VCC port of the receiver, on the same time the two LED are flashing
DPress and hold the button on the transmitter, and then switch on the power supply.
FRelease the match button on the transmitter, take out the match line.
EObserve the LED on the receiver, if found that the LED is not flash anymore and that means successful
GInstall the server and then test.
HIf the tests fail, please repeat the action above.
IIf the tests success, then insert the power supply port into VCC, match complete.
(The above ways of match is only suitable on FLYSKY 2.4G products)
Our products are well matched in the factory, you do not need to match by yourself. But if your
are going to match the receiver with other transmitter, or you need to change a new receiver
or transmitter please follow the following steps:
and this means the receiver are going to the match status.
Matched. This process about 5s˄
Ⴄಏݨڄ඙ዠ۞ڏ෰ሞટ൨ߖ˨ഠႰᅶᐖ൨ߖޱᐗ؏ଙ༓ቫȣݏ຅ഠᇴ༯ࢸ௹ၖ
ݨࠂ໠৒ઌᅞ൨ߖ༓ቫ˨৊ፃഠᇴࢺওᅐݨ༯৒৊ፃࠂ໠৒˨หഠւ຅ჲݨه્ઌᅞ˶
ᏂႤಏݨ༯ࠂ໠ქဧمࢸෆྴ඙ൊ๻
༯৒ދۀٯຉ༯৒ݨလݤପܑ་ଙ଄ݡ༯৒ݨዠຽ཰ؙܑ༘༯৒ઌຉ൨VCC LED
ࣷٶ༯৒໋ݨ຅ࠂᄆمዟຽ཰ؙ༘൨ߖڱࣂᏂܑڴܹዂ་ၼᐓቺ˥LED LED 5S
ࠂ໠৒Ꮠދۀ˨جࣴ؁ࠂ໠৒ȣ2 4G
൨ߖᄏٯຉ༯৒ݨလݤପˤ຅ူ˥BIND CH3
ࠂ໠৒໋ݨ൨ߖւᏁ˨๙ܸૺࠂ໠৒ދኺૺࣴȣˤᏂ˶مᇴཱྀૺւ˥ȣBIND
ཱྀૺࠂ໠৒໋ݨ൨ߖւ֜ޘ༯৒໋ݨ൨ߖᄏ
ཽ࡞ෙᏐ໋جလދ٬༮
຅٬༮ዸ᎚ࡲሞ໋ޱᐗNG
຅٬༮˨ዸދኺါٯຉ˨൨ߖၞڱȣOK VCC
Ꮒሞ໋൨ߖࠝࠈઊ༤ኂݨڄ඙ȣFLYSKY 2 4G
ߖᏔ࿂
LED
Battery
ދۀ
Receive
༯
ߖౕւഩ

Fly Sky FS-GT3 Specifications

General

Brand	Fly Sky
Model	FS-GT3
Category	Remote Control
Language	English