Fly Sky FS-i10 User Manual (English)

Questions and Answers:

R
Richard FitzgeraldJul 30, 2025
Why is Fly Sky Remote Control distance not enough?
- A
  Angela BrownJul 30, 2025
  Why is the Fly Sky Remote Control distance not enough? This could be due to several reasons: * The transmitter or receiver antenna position might be incorrect. Try adjusting their positions. * Radio interference from nearby sources can reduce the control distance. Move away from potential interference. * A low battery can affect the signal strength. Replace the battery. * Obstacles blocking the signal path can also reduce distance. Remove any obstructions between the transmitter and receiver.
M
Michael MartinezAug 4, 2025
How to fix Fly Sky Remote Control that will not turn on?
- S
  saranelsonAug 4, 2025
  How to fix a Fly Sky Remote Control that will not turn on? Here are a few things to check: 1. Make sure the battery is correctly installed. 2. The battery may be empty, try replacing it. 3. The battery shrapnel might be oxidized or have loose contact. Clean the shrapnel and make sure the contact is proper. If the above steps don't work, try charging or replacing the battery.
A
Ariana WebbAug 7, 2025
What to do if Fly Sky FS-i10 Remote Control transmitter can't control the receiver?
- J
  Jessica WardAug 7, 2025
  What to do if the Fly Sky Remote Control transmitter can't control the receiver? It's possible the transmitter or receiver accidentally entered bound status. Try powering them on again, and if necessary, re-bind them.
J
Jon ClarkeAug 12, 2025
Why does item number of acquisition module not appear on Fly Sky FS-i10 Remote Control screen?
- Y
  yangstephanieAug 12, 2025
  Why does the item number of the acquisition module not appear on the Fly Sky Remote Control transmitter screen? This could be because the data cable of the acquisition module is connected incorrectly. Reconnect it properly. Alternatively, the plug of the data cable might be damaged; if so, replace it.
T
Thomas YoungAug 16, 2025
What causes Fly Sky FS-i10 Remote Control transmitter to not accept data when people race?
- J
  Jeffrey PowersAug 16, 2025
  What causes a Fly Sky Remote Control transmitter to sometimes not accept data from the receiver when many people race? This can happen if the distance between two transmitters is too close. Keep the distance between transmitters more than 5 meters.
S
Scott DavisAug 21, 2025
What causes unstable data speed acquisition on Fly Sky FS-i10?
- K
  Kelly NelsonAug 21, 2025
  What causes unstable data speed acquisition on Fly Sky Remote Control? It may be caused by the speed sensor being improperly positioned or drifting too far. Try adjusting the position of the speed sensor.
B
Brooke BarberAug 25, 2025
Why can't simulator be checked on computer with Fly Sky Remote Control?
- K
  kristahallAug 25, 2025
  Why can't the simulator be checked on the computer with Fly Sky Remote Control? The USB simulator function of the transmitter might not be activated. Activate the USB simulator function.

Fly Sky FS-i10 Specifications

General

Channels	10
Frequency	2.4GHz
Modulation	GFSK
2.4G System	AFHDS 2A
RF Power	<20dBm
Range	1.5km
Bandwidth	500kHz
Sensitivity	-105dBm
Low Voltage Warning	Yes
DSC Port	Yes
Antenna Length	26mm
Online Update	Yes
Model Memory	20
Model Type	Helicopter, Airplane, Glider
Display Mode	LCD
Display	Color LCD
Charging Time	4 hours

Summary

Introduction and Services

1. Introduction

Introduces the FS-i10 system and provides guidance for new users.

2. Services

Provides guidance on obtaining assistance and support for system issues.

Symbols and Safety Guide

3. Special symbols

Explains the meaning of symbols used throughout the manual for safety and operation.

4. Safety guide

Details critical safety precautions for operating the RC system and models.

System Specifications and Characteristics

5.2.4GHz System Specifications

Lists the technical specifications of the 2.4GHz radio transmission system.

6. System characteristics

Describes the features, technologies, and error rate indicator of the radio system.

7. Battery charging instructions

Provides instructions for safely charging and maintaining batteries for the system.

System Overview and Transmitter Details

8. System Overview

Provides a general overview of the FS-i10 transmitter's features and capabilities.

9. Transmitter specifications

Lists the detailed technical specifications of the FS-i10 transmitter.

Receiver Specifications and Modules

10. Receiver specifications

Lists the detailed technical specifications of the FS-iR10 receiver.

10.01. RPM Telemetry (magnetic) module

Specifications for the magnetic RPM telemetry module.

10.02. RPM Telemetry (optical) module

Specifications for the optical RPM telemetry module.

10.03. Temperature telemetry module

Specifications for the temperature telemetry module.

More Receiver Modules and Connections

10.04. Voltage telemetry module

Specifications for the voltage telemetry module.

10.05. i-bus receiver

Specifications for the i-bus receiver.

10.06. RPM Telemetry (magnetic) module

Specs for FS-CPD01 magnetic RPM telemetry module.

10.07. RPM Telemetry (optical) module

Specs for FS-CPD02 optical RPM telemetry module.

Module Specs and Connection Guide

10.08. Temperature telemetry module

Specs for FS-CTM01 temperature telemetry module.

10.09. Voltage telemetry module

Specs for FS-CVT01 voltage telemetry module.

10.10. i-bus receiver

Specs for FS-CEVO4 i-bus receiver.

11. Receiver and servo connections

Guidance on correctly connecting receivers and servos for operation.

Model Installation Guide

11.01 Airplane model installation

Steps for installing the receiver and servos in an airplane.

11.02 Helicopter model installation

Steps for installing the receiver and servos in a helicopter.

Receiver Operations

12. Receiver operation instruction

General instructions for operating the receiver.

12.01 Port Setup

Describes the various ports on the receiver and their functions.

12.02 Binding Setup

Step-by-step guide on how to bind the transmitter and receiver.

Module Setup Procedures

12.03 FS-AEV01 i-bus Receiver Connection instruction Setup

Setup guide for connecting the FS-AEV01 i-bus receiver.

12.04 FS-AP001 RPM telemetry (magnetic) module setup

Setup guide for the FS-AP001 magnetic RPM telemetry module.

More Module Setup Guides

12.05 FS-AP002 RPM Telemetry (optical) module setup

Setup guide for the FS-AP002 optical RPM telemetry module.

12.06 FS-ATMO1 Temperature telemetry module connection setup

Setup guide for the FS-ATMO1 temperature telemetry module.

12.07 FS-AVTO1 External voltage telemetry module connection setup

Setup guide for the FS-AVTO1 external voltage telemetry module.

Additional Module and Receiver Setup

12.08 FS-CEV04i-bus Receiver Connection instruction Setup

Setup guide for the FS-CEV04 i-bus receiver.

12.09 FS-CPD01 RPM telemetry (magnetic) module setup

Setup guide for the FS-CPD01 magnetic RPM telemetry module.

Final Module Setup Guides

12.10 FS-CPD02 RPM Telemetry (optical) module setup

Setup guide for the FS-CPD02 optical RPM telemetry module.

12.11 FS-CTM01 Temperature telemetry module connection setup

Setup guide for the FS-CTM01 temperature telemetry module.

12.12 FS-CVT01 External voltage telemetry module connection setup

Setup guide for the FS-CVT01 external voltage telemetry module.

13. Control Parts Descriptions

Identifies and describes the various control parts of the transmitter.

14. Stick mode adjustment

Instructions for changing the transmitter's stick mode configuration.

Power On and Off Procedures

15. Power On

Step-by-step guide for powering on the transmitter and receiver.

15.01 Boot Abnormal Protection

Troubleshooting steps for system startup errors.

16. Power off

Step-by-step guide for powering off the transmitter and receiver.

16.01 Shutdown Abnormal Protection

Procedures to avoid abnormal shutdown when powering off.

17. Logo/Information Screen

Displays the initial FlySky logo and system information screen.

Menu Navigation and System Status

18. Main menu

Overview of how to navigate and access the main menu functions.

19. System Status

Displays the current status of the transmitter and receiver system.

General Function Descriptions

20. General Functions Description

Overview of user interface objects and function controls.

20.01 Introduction

Overview of user interface objects and function controls.

20.02 Switch Function Details

Explanation of how switches and knobs control functions.

20.03 Reset Function Details

How to reset functions to default settings.

Menu Navigation and Dialog Settings

20.04 Online Help Function Details

Instructions on how to access and use the online help feature.

20.05 Scrolling Menu Details

How to navigate through menus using scrolling.

Advanced Menu Functions

20.06 Vertical Scrolling Function Details

Detailed explanation of vertical menu scrolling.

20.07 Multi-function dialog settings

How to use dialog boxes for setting parameters.

General Function Menu: Basic Adjustments

21. General function menu

Access to various general function adjustments.

21.01. Reverse

Adjusts servo direction of operation for each channel.

21.02. End points

Controls low and high travel limits for each servo.

21.03. Subtrim

Adjusts the center position and angle difference for servos.

Function Adjustments: Trims and Exponentials

21.04 Trims

Adjusts the center position of servos and displays trim conditions.

21.05. Scaling Exponentials

Sets dual rate and exponential for improved flight control.

Mixing Functions: Aileron and Rudder

21.06. Aileron to rudder

Creates coordinated turns by mixing aileron and rudder.

21.07. Rudder to aileron

Counteracts roll by mixing rudder and aileron inputs.

Throttle Control Functions

21.08. Throttle Curve

Adjusts the throttle output curve for optimal flight performance.

21.09. Throttle Delay

Reduces throttle response speed to simulate turbine engine airbrake.

Throttle and Auxiliary Channel Settings

21.10. Throttle Down

Enables idle down rate adjustment and throttle cut function.

21.11. Auxiliary Channels

Allows setting additional auxiliary channels for aircraft functions.

Channel Adjustments and Delays

21.12. Channels offset

Revises model parameters for structural deviations.

21.13. Function Delay

Slows down response speed for specific functions like flap movement.

21.14. Channels delay

Slows down response speed for channel outputs like flap delay.

Mix Control Functions

21.15. Linear mixes

Sets up mix controls between sticks, functions, and output channels.

21.16. Curve Mixes

Applies curve distribution to slave channel affected by master channel.

Conditions and Delays

21.17. Conditions

Selects and customizes flight conditions for various functions.

21.18. Conditions Delay

Sets delay for each channel to enhance stability during state changes.

Logic Switches and Airplane Structure

21.19. Logic switches

Combines switches and logic for controlling functions like engine cut.

21.20. Airplane structure

Configures the aircraft structure (e.g., engine, ailerons, flaps).

Timers and Trainer Mode

21.21. Timers

Used for controlling time and reducing aircraft crashing risks.

21.22 Trainer Mode

Connects two transmitters for instructor/student control.

Servo Display and Model Management

21.23.Display servos

Displays real-time servo positions and tests output channels.

21.24.Models

Manages and saves up to twenty different model configurations.

Model Configuration Management

Copy model

Copies model configurations between different slots.

Export models

Saves current model parameters to an SD card.

Import models

Loads model parameters from an SD card.

Delete files

Deletes model files from the SD card.

Model Type and Receiver Setup

Setting model type

Resets model settings to default for airplane or glider types.

21.25 RX setup

Configures receiver settings and connected sensors.

Bind with a receiver

Procedure to bind the transmitter and receiver.

RX battery monitor

Monitors receiver battery voltage and sets alarms.

Receiver and Telemetry Functions

Receiver update

Updates the receiver's firmware via the transmitter.

RX PPM output

Configures CH1 for PPM output, enabling 8-channel operation.

Range test

Checks radio frequency performance by reducing transmitter power.

I-Setup utility

Sets up ESC and other equipment like GPS modules.

Failsafe Function

failsafe function

Configures failsafe behavior for channels upon signal loss.

Setup

Configures failsafe behavior for channels upon signal loss.

Sensor and Telemetry Display

Display sensors

Shows type, ID, and value of connected sensors.

Choose sensors

Selects which sensors to display on the main screen.

Speed and distance

Sets up virtual speed and odometer sensors for telemetry.

Speed and Distance Configuration

Speed sensor

Selects the rotation speed sensor for telemetry data.

Set rotation length

Defines model travel distance per wheel revolution for telemetry.

Reset odometer

Resets odometer 1 (single use) or odometer 2 (total distance).

System and Servo Settings

i-bus setup

Attributes channels to servos connected via the external serial interface.

Servo frequency selection

Adjusts servo frequency from 50Hz to 380Hz.

System Settings

Configures LCD backlight timeout, brightness, and sound alerts.

System Configuration Options

Screen Calibration

Calibrates the touch screen by touching cross center points.

Units

Selects length and temperature units (Metric/Imperial, Celsius/Fahrenheit).

USB function

Configures USB interface for charging or simulator use.

Sticks mode

Switches between different stick mode configurations.

System Management

Language

Sets the user interface language for the transmitter.

Factory reset

Resets all transmitter configurations to their default factory settings.

Firmware update

Guides on updating the transmitter's internal software.

About FS-i10

Displays information about the FS-i10 transmitter and firmware version.

Airplane/Glider Exclusive Functions

22. Airplane/glider exclusive function menu

Access to airplane/glider specific function menus.

22.01 Aileron function

Adjusts aileron function for optimal control.

22.02. Flap function

Adjusts up/down travel of flaps independently for wing types.

22.03 Spoiler function

Adjusts spoiler end points for braking during landing.

More Airplane Functions

22.04 Elevator to flap

Mixes elevator and flap for somersault maneuvers.

22.05 Throttle needle

Sets throttle needle according to engine power for best flight effect.

Additional Airplane Functions

22.06 Butterfly

Provides powerful brake operation by mixing ailerons and flaps.

22.07 Elevator function

Adjusts the proportion of the two elevators' end points.

Rudder, V-Tail, and Structure Settings

22.08 Rudder function

Adjusts the proportion of the two rudders' end points.

22.09V-tail

Controls elevator and rudder for V-tail models.

22.10. Airplane structure

Configures the aircraft structure type (fixed wing/glider).

Helicopter Exclusive Functions

23. Helicopter exclusive function menu

Access to helicopter specific function menus.

23.01.Throttle hold

Maintains throttle channel position for auto-rotation landing.

23.02. Throttle mix

Mixes aileron, elevator, and rudder channels for special functions.

23.03. Pitch curve

Adjusts helicopter pitch for optimal flight effect.

Helicopter Swashplate and Governor Settings

23.04. Swashplate mix

Mixes helicopter aileron, elevator, and pitch for best flight effect.

23.05.structure

Sets helicopter structure types (fixed pitch, variable pitch, etc.).

23.06. Swashplate type

Selects desired swash plate structure type from seven options.

Helicopter Governor and Gyroscope Settings

23.07. Swashplate ring

Sets limitation for swash plate travel for best flight effect.

23.08. Governor

Maintains propeller speed for helicopter operation.

23.09. Gyroscope

Adjusts gyro sensitivity for helicopter flight stability.

23.10. Hover trim

Assigns a knob for adjusting helicopter pitch to maintain hover.

24. Warning function introduction

Explains audible and LED indicator alarms for system warnings.

25. Troubleshooting guide

Provides solutions for common problems encountered with the system.

26. Function tree

Visual representation of input and airplane processing functions.

Helicopter Processing and Output

Helicopter processing

Detailed processing flow for helicopter-specific functions.

27. Packaging content

Lists all items included in the product package.

28. FCC Statement

Compliance information regarding FCC regulations for radio frequency devices.

Related product manuals

Fly Sky FS-i10 User Manual

Table of Contents

Questions and Answers:

Fly Sky FS-i10 Specifications

Summary

Introduction and Services

1. Introduction

2. Services

Symbols and Safety Guide

3. Special symbols

4. Safety guide

System Specifications and Characteristics

5.2.4GHz System Specifications

6. System characteristics

7. Battery charging instructions

System Overview and Transmitter Details

8. System Overview

9. Transmitter specifications

Receiver Specifications and Modules

10. Receiver specifications

10.01. RPM Telemetry (magnetic) module

10.02. RPM Telemetry (optical) module

10.03. Temperature telemetry module

More Receiver Modules and Connections

10.04. Voltage telemetry module

10.05. i-bus receiver

10.06. RPM Telemetry (magnetic) module

10.07. RPM Telemetry (optical) module

Module Specs and Connection Guide

10.08. Temperature telemetry module

10.09. Voltage telemetry module

10.10. i-bus receiver

11. Receiver and servo connections

Model Installation Guide

11.01 Airplane model installation

11.02 Helicopter model installation

Receiver Operations

12. Receiver operation instruction

12.01 Port Setup

12.02 Binding Setup

Module Setup Procedures

12.03 FS-AEV01 i-bus Receiver Connection instruction Setup

12.04 FS-AP001 RPM telemetry (magnetic) module setup

More Module Setup Guides

12.05 FS-AP002 RPM Telemetry (optical) module setup

12.06 FS-ATMO1 Temperature telemetry module connection setup

12.07 FS-AVTO1 External voltage telemetry module connection setup

Additional Module and Receiver Setup

12.08 FS-CEV04i-bus Receiver Connection instruction Setup

12.09 FS-CPD01 RPM telemetry (magnetic) module setup

Final Module Setup Guides

12.10 FS-CPD02 RPM Telemetry (optical) module setup

12.11 FS-CTM01 Temperature telemetry module connection setup

12.12 FS-CVT01 External voltage telemetry module connection setup

13. Control Parts Descriptions

13. Control Parts Descriptions

14. Stick mode adjustment

14. Stick mode adjustment

Power On and Off Procedures

15. Power On

15.01 Boot Abnormal Protection

16. Power off

16.01 Shutdown Abnormal Protection

17. Logo/Information Screen

17. Logo/Information Screen

Menu Navigation and System Status

18. Main menu

19. System Status

General Function Descriptions

20. General Functions Description

20.01 Introduction

20.02 Switch Function Details

20.03 Reset Function Details

Menu Navigation and Dialog Settings

20.04 Online Help Function Details

20.05 Scrolling Menu Details

Advanced Menu Functions

20.06 Vertical Scrolling Function Details

20.07 Multi-function dialog settings

General Function Menu: Basic Adjustments