FMC Technologies Smith Meter AccuLoad III.net

Contents
Section I – Introduction ...........................................................................................................................................1
Section II – Connecting via Ethernet .....................................................................................................................2
Configuring the AccuLoad.net for Ethernet Communications .............................................................................2
Configuring Windows 2000/XP for Ethernet Connection to AccuLoad.net .......................................................... 3
Section III – Configuring a SLIP Connection ........................................................................................................5
AccuLoad Settings for SLIP Communications ..................................................................................................... 5
PC Settings for SLIP Communications ................................................................................................................ 6
Section IV – Using the TCP/IP Link ........................................................................................................................8
Checking the TCP/IP Connection ........................................................................................................................ 8
Section V – Firmware Upgrade Procedure ............................................................................................................9
Upgrading the Firmware with the AccuLoad.net .................................................................................................9
Procedure for Upgrading Firmware .....................................................................................................................9
Troubleshooting .................................................................................................................................................13
Appendix – Troubleshooting TCP/IP Communications ......................................................................................14
Troubleshooting an Ethernet Connection ..........................................................................................................14
Troubleshooting a SLIP Connection ..................................................................................................................14
Issue/Rev. 0.2 (6/14) Bulletin AB06069
The Most Trusted Name In Measurement
Application Manual
TCP/IP (Ethernet & Slip) Communications
and Upgrading Firmware
Smith Meter
®
AccuLoad
®
III.net

FMC Technologies Smith Meter AccuLoad III.net Specifications

General

Model	AccuLoad III.net
Manufacturer	FMC Technologies Smith Meter
Category	Measuring Instruments
Enclosure Rating	NEMA 4X
Display	LCD
Application	Liquid Measurement and Control
Operating Temperature	-40°C to +60°C (-40°F to +140°F)
Communication Protocol	Modbus, Ethernet
Power Supply	24 VDC or 120/230 VAC
Flow Rate Range	Varies depending on meter and application

Summary

Introduction to TCPIP Communications and Basic Networking

TCPIP Protocol Overview

Defines TCP/IP as the standard protocol for Internet communications.

Ethernet Basics

Explains Ethernet as a low-level protocol for hardware link between devices.

Network Addressing Concepts

Details IP Address, Net Mask, MAC Address, and Gateway definitions.

Connecting via Ethernet

AccuLoad.net Ethernet Configuration Steps

Step-by-step guide to configure AccuLoad.net network settings.

Network Topology Recommendation

Suggests using a private network for AccuLoad.net connections.

Windows XP Ethernet Connection Setup

Lists requirements and connection methods for PC setup.

Physical Ethernet Connection Methods

Explains machine-to-machine vs. hub connection methods.

Initiating PC Network Connection Setup

Guides user to access Windows Network Connections.

Configuring TCPIP Properties in Windows

Details setting IP address, subnet mask, and gateway in Windows.

Configuring a SLIP Connection

AccuLoad.net SLIP Configuration Settings

Configures AccuLoad.net serial ports for SLIP.

SLIP Host Interface Settings

Sets IP address, network, and gateway for SLIP.

Windows XP SLIP Connection Wizard Steps

Guides through creating a SLIP connection in Windows.

Configuring SLIP COM Port Baud Rate

Sets baud rate and other serial parameters for SLIP.

SLIP Dial-up Server and Protocol Settings

Selects SLIP server type and network protocols.

Assigning PC IP Address for SLIP

Sets PC IP address for SLIP connection.

Using the TCPIP Link

Establishing and Verifying TCPIP Connection

Steps to launch AccuMate and confirm connection status.

Accessing AccuLoad via Web and FTP

Using HTTP interface and FTP for file transfer.

Firmware Upgrade Procedure

Firmware Upgrade Overview and Key Requirements

Explains firmware upgrade process and necessary keys.

Procedure for Upgrading Firmware

Detailed steps for performing a firmware upgrade.

Specifying Firmware Upgrade Key File

Locating the .A3Key file for the upgrade.

Entering Access Code for Upgrade

Inputting the security access code to authorize upgrade.

Firmware Upgrade Troubleshooting Tips

Addresses common issues like AccuMate version, keys, and connection errors.

Firmware Upgrade Switch Settings

Explains DIP switch configurations for bootloader.

Troubleshooting TCPIP Communications

Ethernet Connection Troubleshooting

Interpreting LEDs, using PING, and packet sniffers.

SLIP Connection Troubleshooting

Using Comm Monitor and diagnosing handshake/IP issues.

Checking PC Serial Port Settings

Verifying COM port parameters using command line tools.