Fronius MagicWave 1700

Questions and Answers

R
Robert ShortAug 18, 2025
What to do if the Fronius MagicWave 1700 displays 'Ignition time-out'?
- A
  Aaron MoranAug 18, 2025
  If the Fronius Welding System indicates an 'Ignition time-out', it means the current didn't start flowing before the set wire length was fed, and the power source safety cut-out was activated. Try pressing the torch trigger repeatedly. Also, clean the workpiece surface. If the problem persists, increase the time until the safety cut-out is triggered via the level 2 setup menu.
S
stephenjohnstonAug 20, 2025
What to do if Fronius Welding System shows error 'PE'?
- S
  shannon26Aug 20, 2025
  If your Fronius Welding System displays error 'PE', the earth current watchdog has triggered the power source's safety cut-out. To resolve this, switch off the power source, wait 10 seconds, and then switch it back on. If the error continues after several attempts, the provided information is insufficient to resolve this issue.
R
rogersdeborahAug 23, 2025
What to do if Fronius MagicWave 1700 tP1 error occurs?
- S
  sberryAug 23, 2025
  If the Fronius Welding System displays a tP1 error, it indicates overtemperature in the power source's primary circuit. Allow the power source to cool down.
B
Benjamin CunninghamAug 26, 2025
What to do if Fronius MagicWave 1700 tP2 error occurs?
- T
  Tara LesterAug 26, 2025
  If the Fronius Welding System displays a tP2 error, it indicates overtemperature in the power source's primary circuit. Allow the power source to cool down.
N
Nicholas MathewsAug 27, 2025
What to do if Fronius MagicWave 1700 tP3 error occurs?
- M
  Michelle HardyAug 28, 2025
  If the Fronius Welding System displays a tP3 error, it indicates overtemperature in the power source's primary circuit. Allow the power source to cool down.
S
Sheryl ShermanAug 30, 2025
What to do if Fronius MagicWave 1700 Welding System tP4 error occurs?
- C
  Clifford ReeseAug 30, 2025
  If the Fronius Welding System displays a tP4 error, it indicates overtemperature in the power source's primary circuit. Allow the power source to cool down.
T
tonyacruzSep 1, 2025
What to do if Fronius MagicWave 1700 tP5 error occurs?
- C
  Casey JohnsonSep 1, 2025
  If the Fronius Welding System displays a tP5 error, it indicates overtemperature in the power source's primary circuit. Allow the power source to cool down.
M
masonjuliaSep 4, 2025
What to do if Fronius Welding System tP6 error occurs?
- M
  Melissa WelchSep 4, 2025
  If the Fronius Welding System displays a tP6 error, it indicates overtemperature in the power source's primary circuit. Allow the power source to cool down.
R
Robin AndersonSep 6, 2025
What to do if Fronius Welding System tS1 error occurs?
- C
  Christopher JohnsonSep 6, 2025
  If the Fronius Welding System displays a tS1 error, it indicates overtemperature in the power source's secondary circuit. Allow the power source to cool down.
D
Derek GrossSep 9, 2025
What to do if Fronius Welding System tS2 error occurs?
- K
  Kimberly NicholsSep 9, 2025
  If the Fronius Welding System displays a tS2 error, it indicates overtemperature in the power source's secondary circuit. Allow the power source to cool down.