EasyManua.ls Logo

Fronius TransTig 1700 - User Manual

Fronius TransTig 1700
124 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Op erating
Instructions
TransTig 800
TransTig 2200
TransTig 2500 / 3000
TransTig 4000 / 5000
MagicWave 1700 / 2200
MagicWave 2500 / 3000
MagicWave 4000 / 5000
42,0426,0027,EN 023-21092022
EN
Operating instructions

Table of Contents

Other manuals for Fronius TransTig 1700

Preview: Operating Instructions/Spare Parts List
Operating Instructions/Spare Parts List98 pages
Preview: Operating Instructions And Spare Parts List
Operating Instructions And Spare Parts List58 pages

Questions and Answers

  • D
    Daniel PetersJul 26, 2025
    What to do if Fronius Welding System has no shielding gas?
    • A
      Autumn BarnesJul 26, 2025
      If your Fronius Welding System has no shielding gas, the gas cylinder might be empty, so you should change the gas cylinder. The pressure regulator could be defective, in this case you should change the regulator. The gas hose may not be connected or is faulty, so connect the gas hose or replace it if it's faulty. The welding torch could be faulty, so replace the torch. If the gas solenoid valve is defective, call after-sales service.
  • A
    Alyssa GentryJul 31, 2025
    What to do if Fronius Welding System has poor arc ignition?
    • M
      Marilyn SmithJul 31, 2025
      If your Fronius Welding System demonstrates poor arc ignition, first increase the gas pre-flow time. If HF is too weak, see Pt.9 below. If the tungsten electrode is alloyed up, or the pointed tip is damaged, sharpen the tip of the tungsten electrode. If the tungsten electrode is underloaded, use a suitable electrode for the amperage (also start-arc amperage) in question. If the gas nozzle is dirty and HF jumps over the gas nozzle onto the workpiece, use a new ceramic nozzle. If the gas nozzle is too small for the diameter of tungsten electrode used, use a bigger gas nozzle. If the torch is damaged (torch body, protective hose etc. are faulty), replace the damaged parts or change the torch.
  • J
    Jennifer MontgomeryAug 4, 2025
    What to do if Fronius Welding System has no welding current?
    • J
      Jeremy LambertAug 4, 2025
      If your Fronius Welding System has no welding current, ensure the earth cable is correctly clamped to the workpiece. Check that the earth cable is plugged into the correct socket and is secure. If the torch is faulty, replace it. If there's a short circuit in the welding-current circuit in electrode welding mode (longer than 1 sec.), eliminate the short circuit.
  • R
    Robert DaviesAug 9, 2025
    What to do if Fronius Welding System remote control unit does not work?
    • J
      Joseph HernandezAug 9, 2025
      If the remote control unit of your Fronius Welding System isn't working (but other functions are OK), make sure the remote control cable is properly connected. If the remote control unit or cable is faulty, replace it. If the 10-pole remote control socket is faulty, replace the remote control socket.
  • D
    Danielle DavisAug 14, 2025
    What to do if there is no reaction when torch trigger is actuated on Fronius Welding System?
    • M
      Matthew BrooksAug 14, 2025
      If there's no reaction when you actuate the torch trigger on your Fronius Welding System, first ensure the torch control plug is correctly plugged in and secured; check the connection and replace if necessary. If the torch switch (micro-switch) or torch control line is faulty, repair or replace the torch. Also, ensure that the "Power ON" reset time after switch-on (10 sec) has elapsed; wait for about 10 seconds after switching on the mains switch before starting to weld.
  • E
    Erica ColeAug 20, 2025
    What to do if arc sometimes breaks in manual electrode Fronius Welding System?
    • R
      Raymond OwensAug 20, 2025
      If the arc sometimes breaks in manual electrode mode on your Fronius Welding System, it could be because the arc-drop voltage of the electrode is too high. If possible, use an alternative electrode.

Summary

Safety Rules and Precautions

Safety Notices Explained

Explains DANGER, WARNING, CAUTION, and NOTE symbols for safety.

Operator and Personnel Responsibilities

Hazard Identification and Prevention

Covers electrical, toxic gas, flying sparks, EMC, and specific hazards.

Installation, Operation, and Maintenance Safety

Safety during setup, normal operation, maintenance, and disposal.

Installation and Commissioning Procedures

Pre-Installation Requirements

Electrical Connections and Start-up

Covers generator power, mains cable, gas cylinder, grounding, and torch connection.

Initial Power Source Start-up

Troubleshooting and Maintenance

Troubleshooting Common Errors

Identifies error codes, causes, and remedies for device issues.

Routine Maintenance and Disposal

Fronius TransTig 1700 Specifications

General IconGeneral
BrandFronius
ModelTransTig 1700
CategoryWelding System
LanguageEnglish

Related product manuals