Fronius TransTig 2500

Questions and Answers

S
Sherry OconnellAug 17, 2025
What to do if the Fronius TransTig 2500 Welding System displays 'Ignition time-out'?
- T
  Terri ValdezAug 17, 2025
  If the Fronius Welding System indicates an 'Ignition time-out', it means the current didn't start flowing before the set wire length was fed, and the power source safety cut-out was activated. Try pressing the torch trigger repeatedly. Also, clean the workpiece surface. If the problem persists, increase the time until the safety cut-out is triggered via the level 2 setup menu.
E
Edward MartinezAug 20, 2025
What to do if Fronius TransTig 2500 shows error 'PE'?
- A
  Andrew IngramAug 20, 2025
  If your Fronius Welding System displays error 'PE', the earth current watchdog has triggered the power source's safety cut-out. To resolve this, switch off the power source, wait 10 seconds, and then switch it back on. If the error continues after several attempts, the provided information is insufficient to resolve this issue.
D
Deborah LopezAug 22, 2025
What to do if Fronius TransTig 2500 Welding System tP1 error occurs?
- M
  melaniefrenchAug 22, 2025
  If the Fronius Welding System displays a tP1 error, it indicates overtemperature in the power source's primary circuit. Allow the power source to cool down.
J
john51Aug 26, 2025
What to do if Fronius TransTig 2500 Welding System tP2 error occurs?
- C
  Christopher FosterAug 26, 2025
  If the Fronius Welding System displays a tP2 error, it indicates overtemperature in the power source's primary circuit. Allow the power source to cool down.
L
Lydia MorrisonAug 27, 2025
What to do if Fronius Welding System tP3 error occurs?
- R
  Robert GreenAug 27, 2025
  If the Fronius Welding System displays a tP3 error, it indicates overtemperature in the power source's primary circuit. Allow the power source to cool down.
J
Joshua HarrisAug 30, 2025
What to do if Fronius TransTig 2500 tP4 error occurs?
- S
  Sharon GutierrezAug 30, 2025
  If the Fronius Welding System displays a tP4 error, it indicates overtemperature in the power source's primary circuit. Allow the power source to cool down.
M
melissafullerSep 1, 2025
What to do if Fronius Welding System tP5 error occurs?
- B
  Brian Good Jr.Sep 1, 2025
  If the Fronius Welding System displays a tP5 error, it indicates overtemperature in the power source's primary circuit. Allow the power source to cool down.
H
Haley TurnerSep 4, 2025
What to do if Fronius TransTig 2500 tP6 error occurs?
- R
  Ruth CostaSep 4, 2025
  If the Fronius Welding System displays a tP6 error, it indicates overtemperature in the power source's primary circuit. Allow the power source to cool down.
M
Mary MontesSep 6, 2025
What to do if Fronius TransTig 2500 Welding System tS1 error occurs?
- H
  Heidi SchwartzSep 6, 2025
  If the Fronius Welding System displays a tS1 error, it indicates overtemperature in the power source's secondary circuit. Allow the power source to cool down.
S
sheaannetteSep 9, 2025
What to do if Fronius Welding System tS2 error occurs?
- B
  Brian HolmesSep 9, 2025
  If the Fronius Welding System displays a tS2 error, it indicates overtemperature in the power source's secondary circuit. Allow the power source to cool down.