Frontier ST1332 - User Manual

Questions and Answers

R
Renee GarciaAug 19, 2025
Why does my Frontier ST1332 engine run erratically?
- T
  Tricia ClarkAug 19, 2025
  If your Frontier Snow Blower engine runs erratically, it might be due to a blocked fuel line, which requires cleaning. Another cause could be an empty gas tank, so check the fuel supply. Stale gasoline can also lead to this issue; adding fresh gasoline with a fuel stabilizer might help. Lastly, water or dirt in the fuel system could be the culprit. In this case, remove the carburetor bowl to drain the fuel tank and refill it with fresh fuel. Remember, don't remove the carburetor bowl when the engine is hot.
S
samuel20Aug 22, 2025
What to do if my Frontier ST1332 has loss of power?
- M
  Michelle DavisAug 22, 2025
  If your Frontier Snow Blower is experiencing a loss of power, the gas cap vent hole might be plugged. Remove any ice and snow from the cap, and ensure the vent hole is clear to resolve the issue.
J
johnsonsarahAug 23, 2025
What to do if Frontier ST1332 Snow Blower fails to discharge snow?
- G
  Gregory LaneAug 25, 2025
  If your Frontier Snow Blower unit fails to discharge snow, several issues could be the cause. First, the auger drive belt might be loose or damaged, requiring replacement or adjustment. Second, the auger control cable may not be adjusted correctly, so adjustment is needed. Third, a broken shear bolt could be the problem, necessitating a replacement. Additionally, the discharge chute might be clogged, requiring you to stop the engine immediately and disconnect the spark plug wire before cleaning the discharge chute and the inside of the auger housing. Lastly, a foreign object lodged in the auger could be the cause, requiring you to stop the engine immediately and disconnect the spark plug wire before removing the object from the auger.
M
matthewjonesAug 26, 2025
Why electric grips do not heat and electric chute does not rotate on Frontier ST1332 Snow Blower?
- L
  lisa95Aug 26, 2025
  If the electric grips don't heat and the electric chute doesn't rotate on your Frontier Snow Blower, a blown fuse is a likely cause. Check the fuse and replace it with a 7.5 amp automotive type fuse. Refer to the Wiring Harness parts list page for the location of the fuse.
M
monica85Aug 28, 2025
What to do if Frontier ST1332 unit fails to propel itself?
- F
  Francisco RobinsonAug 28, 2025
  If your Frontier Snow Blower unit fails to propel itself, it could be due to a drive belt that is either loose or damaged, requiring replacement. Alternatively, the traction drive cable might be incorrectly adjusted, which also requires adjustment.
D
David HolmesAug 30, 2025
What to do if my Frontier Snow Blower engine stalls?
- R
  Robert HamiltonAug 30, 2025
  If your Frontier Snow Blower engine stalls, it might be because the unit is running on CHOKE. To fix this, set the choke lever to the RUN position.
S
Stephanie BrownSep 1, 2025
Why does my Frontier ST1332 Snow Blower have excessive vibration?
- S
  Sheila KingSep 1, 2025
  If your Frontier Snow Blower has excessive vibration, it could be due to loose parts or a damaged impeller. Immediately stop the engine and remove the spark plug wire. Tighten all bolts and make any necessary repairs. If the vibration continues, have the unit serviced by a competent repairman.
L
Larry PerezSep 3, 2025
How to fix difficult starting on Frontier ST1332 Snow Blower?
- J
  Jessica JonesSep 3, 2025
  If you're experiencing difficulty starting your Frontier Snow Blower, it might be due to a defective spark plug. Replace the spark plug to resolve this issue.
S
Sarah WhiteSep 5, 2025
What to do if my Frontier ST1332 Snow Blower fails to discharge snow?
- C
  Crystal CarterSep 5, 2025
  If your Frontier Snow Blower is not discharging snow, there could be several reasons: * The auger drive belt may be loose or damaged. You should replace or adjust the auger drive belt. * The auger control cable may not be adjusted correctly. Adjust the auger control cable. * A shear bolt may be broken. Replace the shear bolt. * The discharge chute may be clogged. Stop the engine immediately and disconnect the spark plug wire. Clean the discharge chute and inside of the auger housing. * A foreign object may be lodged in the auger. Stop the engine immediately and disconnect the spark plug wire. Remove the object from the auger.
A
Allison DavisSep 8, 2025
Why is my Frontier ST1332 losing power?
- L
  Linda BowmanSep 8, 2025
  If your Frontier Snow Blower is experiencing a loss of power, the gas cap vent hole might be plugged. Remove any ice and snow from the cap, ensuring the vent hole is clear.

Summary

INTRODUCTION

RESPONSIBILITY OF THE OWNER

Outlines the owner's duties for safe operation and maintenance.

RULES FOR SAFE OPERATION

Operating and Hazard Symbols

Explains symbols used on the equipment and in the manual to indicate risks.

DANGER Warnings

Critical safety warnings for immediate danger, such as rotating parts and thrown objects.

WARNINGs: Fuel, Heat, and Sparking

Safety alerts regarding flammable fuel, hot components, and electrical hazards.

Operational Safety Practices

Guidelines for safe operation, training, and preparation.

Maintenance and Storage Safety

Safety precautions for maintenance, unclogging, and storage.

SAFETY DECALS

Identifying Your Snowthrower

Provides model and serial number information for identification and parts.

OWNERS INFORMATION

THREE YEAR LIMITED WARRANTY

Details the warranty coverage, limitations, and claim procedures for the snowthrower.

ASSEMBLY

Preparation for Assembly

Lists tools, carton contents, and unpacking instructions.

Unpacking the Snowthrower

Step-by-step instructions for safely removing the snowthrower from its shipping carton.

Handle and Cable Assembly

Steps for assembling the upper handle and checking/setting cables.

Control Knobs and Rod Installation

Instructions for installing remote chute and speed control knobs and rod.

Snow Chute and Tire Checks

Procedures for assembling the snow chute and checking tire pressure.

OPERATION

Controls and Operation Overview

Identifies and explains the function of all engine and snowthrower controls.

Snowthrower Operation and Stopping

Guides on how to operate and safely stop the snowthrower.

Controlling Snow Discharge

How to adjust the direction and height of snow thrown.

Moving Forward and Backward

Instructions on how to engage forward and reverse drive.

Throwing Snow

How to engage the auger to start throwing snow.

OPERATION

Wheel Lockout Operation

Instructions for using the wheel lockout feature for maneuverability.

Setting Drift Cutters

Guidance on adjusting drift cutters for deeper snow.

Using Heated Grips

How to operate the heated grips for comfort in cold weather.

OPERATION

Before Starting Engine

Essential checks and procedures before starting the engine.

Fill Gas Tank

Proper procedures for adding fuel to the snowthrower.

OPERATION

Stopping the Engine

Steps to safely shut down the snowthrower engine.

Starting the Engine

Procedures for starting the engine manually or electrically.

Cold Engine Start

Specific steps for starting a cold engine.

OPERATION

Warm Engine Start (Recoil Starter)

How to restart the engine after a brief shutdown.

OPERATION

Frozen Starter Troubleshooting

Steps to take if the starter mechanism is frozen.

Clearing a Clogged Discharge Chute

Safe procedures for removing blockages from the discharge chute.

OPERATION

Operating Tips for Efficiency

Advice for optimizing snowblower performance and maintenance.

SERVICE RECOMMENDATIONS

Maintenance Schedule

A table outlining recommended service intervals for various procedures.

After Each Use Checklist

Tasks to perform after every use for proper upkeep.

MAINTENANCE

Snowthrower Adjustments

Procedures for adjusting snowthrower components like belts.

Auger Gear Box and Shaft Lubrication

Instructions for lubricating the auger gear box and shaft.

Chute Rotation Gear Lubrication

Steps for lubricating the chute rotation gear.

MAINTENANCE

Engine Oil Checks and Changes

Procedures for checking, changing, and draining engine oil.

MAINTENANCE

Auger Housing Height Adjustment

How to adjust the scraper bar and skid heights.

MAINTENANCE

Removing the Snow Hood

Steps to remove the snow hood for accessing engine components.

MAINTENANCE

Traction Drive Belt Adjustment

How to adjust the tension of the traction drive belt.

MAINTENANCE

Auger Drive Belt Adjustment

Steps to adjust the tension of the auger drive belt.

MAINTENANCE

Replacing Drive Belts

Instructions for replacing the auger and traction drive belts.

MAINTENANCE

Belt Guide Adjustments

How to adjust auger and traction drive belt guides.

MAINTENANCE

Cable Adjustments

Procedures for checking and adjusting control cables.

MAINTENANCE

Auger Shear Bolt and Spark Plug Maintenance

How to replace shear bolts and service the spark plug.

STORAGE

Off-Season Storage and Removal

Steps for preparing the snowthrower for storage and removing it afterward.

TROUBLE SHOOTING CHART

Identifying Your Snowthrower

Information on locating model and serial numbers for service.

Summary

INTRODUCTION

RESPONSIBILITY OF THE OWNER

Outlines the owner's duties for safe operation and maintenance.

RULES FOR SAFE OPERATION

Operating and Hazard Symbols

Explains symbols used on the equipment and in the manual to indicate risks.

DANGER Warnings

Critical safety warnings for immediate danger, such as rotating parts and thrown objects.

WARNINGs: Fuel, Heat, and Sparking

Safety alerts regarding flammable fuel, hot components, and electrical hazards.

Operational Safety Practices

Guidelines for safe operation, training, and preparation.

Maintenance and Storage Safety

Safety precautions for maintenance, unclogging, and storage.

SAFETY DECALS

Identifying Your Snowthrower

Provides model and serial number information for identification and parts.

OWNERS INFORMATION

THREE YEAR LIMITED WARRANTY

Details the warranty coverage, limitations, and claim procedures for the snowthrower.

ASSEMBLY

Preparation for Assembly

Lists tools, carton contents, and unpacking instructions.

Unpacking the Snowthrower

Step-by-step instructions for safely removing the snowthrower from its shipping carton.

Handle and Cable Assembly

Steps for assembling the upper handle and checking/setting cables.

Control Knobs and Rod Installation

Instructions for installing remote chute and speed control knobs and rod.

Snow Chute and Tire Checks

Procedures for assembling the snow chute and checking tire pressure.

OPERATION

Controls and Operation Overview

Identifies and explains the function of all engine and snowthrower controls.

Snowthrower Operation and Stopping

Guides on how to operate and safely stop the snowthrower.

Controlling Snow Discharge

How to adjust the direction and height of snow thrown.

Moving Forward and Backward

Instructions on how to engage forward and reverse drive.

Throwing Snow

How to engage the auger to start throwing snow.

OPERATION

Wheel Lockout Operation

Instructions for using the wheel lockout feature for maneuverability.

Setting Drift Cutters

Guidance on adjusting drift cutters for deeper snow.

Using Heated Grips

How to operate the heated grips for comfort in cold weather.

OPERATION

Before Starting Engine

Essential checks and procedures before starting the engine.

Fill Gas Tank

Proper procedures for adding fuel to the snowthrower.

OPERATION

Stopping the Engine

Steps to safely shut down the snowthrower engine.

Starting the Engine

Procedures for starting the engine manually or electrically.

Cold Engine Start

Specific steps for starting a cold engine.

OPERATION

Warm Engine Start (Recoil Starter)

How to restart the engine after a brief shutdown.

OPERATION

Frozen Starter Troubleshooting

Steps to take if the starter mechanism is frozen.

Clearing a Clogged Discharge Chute

Safe procedures for removing blockages from the discharge chute.

OPERATION

Operating Tips for Efficiency

Advice for optimizing snowblower performance and maintenance.

SERVICE RECOMMENDATIONS

Maintenance Schedule

A table outlining recommended service intervals for various procedures.

After Each Use Checklist

Tasks to perform after every use for proper upkeep.

MAINTENANCE

Snowthrower Adjustments

Procedures for adjusting snowthrower components like belts.

Auger Gear Box and Shaft Lubrication

Instructions for lubricating the auger gear box and shaft.

Chute Rotation Gear Lubrication

Steps for lubricating the chute rotation gear.

MAINTENANCE

Engine Oil Checks and Changes

Procedures for checking, changing, and draining engine oil.

MAINTENANCE

Auger Housing Height Adjustment

How to adjust the scraper bar and skid heights.

MAINTENANCE

Removing the Snow Hood

Steps to remove the snow hood for accessing engine components.

MAINTENANCE

Traction Drive Belt Adjustment

How to adjust the tension of the traction drive belt.

MAINTENANCE

Auger Drive Belt Adjustment

Steps to adjust the tension of the auger drive belt.

MAINTENANCE

Replacing Drive Belts

Instructions for replacing the auger and traction drive belts.

MAINTENANCE

Belt Guide Adjustments

How to adjust auger and traction drive belt guides.

MAINTENANCE

Cable Adjustments

Procedures for checking and adjusting control cables.

MAINTENANCE

Auger Shear Bolt and Spark Plug Maintenance

How to replace shear bolts and service the spark plug.

STORAGE

Off-Season Storage and Removal

Steps for preparing the snowthrower for storage and removing it afterward.

TROUBLE SHOOTING CHART

Identifying Your Snowthrower

Information on locating model and serial numbers for service.

Frontier ST1332 Specifications

General

Engine	Briggs & Stratton Intek Snow OHV
Horsepower	13 hp
Starter	Electric / Recoil
Fuel Capacity	4 quarts
Drive System	Hydrostatic
Speeds	Variable Fwd/Rev
Traction Control	Wheel Lock
Clearing Width	32”
Auger Diameter	16”
Auger Type	Steel / Saw Tooth
Impeller Diameter	12”
Chute Rotation	Electric
Chute Turning Radius	190
Deflector Control	Remote
Warranty - Engine	3 years
Warranty - Machine	3 years