Fujitsu PRIMERGY TX150 S2 Configuration Guide

<Restrictions>
(
1
)
Each
p
h
y
sical
p
ack must contain the same Product IDs of HDDs.
(
2
)
Maximum lo
g
ical drive size is 2TB.
One
p
h
y
sical
p
ack is com
p
rised b
y
one lo
g
ical drive
(
A
p
h
y
sical
p
ack is the same ca
p
acit
y
as a lo
g
ical drive
)
.
(
3
)
The number of HDDs com
p
risin
g
a
p
h
y
sical
p
ack is as shown below.
RAID Level Descri
p
tion HDDs Ca
p
acit
y
of lo
g
ical drives
RAID 0 The data is broken down into blocks
,
2~16 The ca
p
acit
y
of lo
g
ical drive is same
each on a se
p
arate disk drive as the ca
p
acit
y
of connected HDD.
RAID 1 Du
p
licates the disk and writes 2 The ca
p
acit
y
of the lo
g
ical drive is
the same data onto two disks. half the ca
p
acit
y
of connected HDD.
RAID 5 The data is broken down into blocks 3~16 The ca
p
acit
y
of each lo
g
ical drive is
and each blocks is written to
g
ethe
r
the number of connected HDDs - 1
)
.
with
p
arit
y
bits on a se
p
arate disk drive.
RAID 0+1 Du
p
licates the disk and broken down 4~16 The ca
p
acit
y
of each lo
g
ical drive
into blocks
,
each on a is the half the ca
p
acit
y
of connected
se
p
arate disk. HDD.
(
4
)
The same RAID level must be used when dividin
g
a
p
h
y
sical
p
ack into a number of lo
g
ical drives.
(
5
)
A
p
h
y
sical
p
ack must contain onl
y
HDDs which are connected b
y
the same RAID Controller.
(
6
)
A RAID Controller can su
pp
ort more than one
p
h
y
sical
p
ack.
(
even if different RAID levels
)
- HDD confi
g
ured
p
h
y
sical
p
ack shall be constent in the
p
roduct ID.
- In the case when several
p
h
y
sical
p
ack confi
g
ured with HDD of same ca
p
acit
y,
the HDD shall be constent in the
p
roduct ID.
(
7
)
When the hot s
p
are disk is installed b
y
com
p
risin
g
more than 2
p
h
y
sical
p
ack contains HDDs with different
p
roduct ID
,
each
p
h
y
sical
p
ack must contain at least one hot s
p
are disk with consistent
p
roduct ID.
(
8
)
In case that the same ca
p
acit
y
HDDs are connected to the same RAID Controller
,
these HDDs must also have the same r
p
m s
p
eed.

Restrictions and Notes of RAID Controller Card
Here are the restrictions and notes of RAID Controller Cards. Please be sure to use
p
roducts
alon
g
with these conditions as follows
;
[
PG-140D
]
1. One Controller Card can be mounted in a server
2. Used onl
y
for internal HDD connection. On board SCSI Controller is used for the connection with internal HDD.
3. For RAID0/1/5
,
When one lo
g
ical drive is exsist in
p
h
y
siacl
p
ack
,
Ph
y
sical Pack Ex
p
ansion kit can be a
pp
lied.
[
PG-141CL
]
1. One Controller Card can be mounted in a server
2. Used onl
y
for internal HDD connection. On board SCSI Controller is used for the connection with internal HDD.
3. For RAID0/1/5
,
When one lo
g
ical drive is exsist in
p
h
y
siacl
p
ack
,
Ph
y
sical Pack Ex
p
ansion kit can be a
pp
lied.
Combination matrix of RAID Controlle
r
* o: Supported
TX150 S2
x: Not Supported

Notes of SCSI Controlle
r
[
PG-130L
]
1. When the external SCSI controller and the internal SCSI controller connected simultaneousl
y,
SCSI Controller must be se
p
arated.
2. Number of the external SCSI Controller can be connected with this SCSI Controller : Max. 2 exce
p
t Backu
p
Cabinet
o
x
PG
-
140D
(
Ultra320 SCSI
,
0ch
)
PG
-
141CL
(
Ultra320 SCSI
,
1ch
)
Internal HDD Internal HDD
RAID Controller / SCSI Controller
36GB
10000rpm
36GB
10000rpm
36GB
10000rpm
36GB
10000rpm
36GB
15000rpm
36GB
15000rpm
ch 0
ch 0
ch 1
ch1
RAID Controller

Fujitsu PRIMERGY TX150 S2 Specifications

General

Brand	Fujitsu
Model	PRIMERGY TX150 S2
Category	Server
Language	English