Fujitsu UTY-RNRGZ5 - Initial Setup

3-8-2 Backlight Setting
(1) Touch the [Backlight Setting]
on the “Preference” screen.
Back
Preference
Panel
Calibration
Backlight
Setting
Contrast
Enable or disable the backlight
(2) “Backlight Setting” screen is displayed. Touch the [En-
able/Disable] on the “Backlight Setting” screen.
(3) “Enable/Disable” screen is displayed. Select the [Enable]
or [Disable].
(2) (3)
Enable/Disable [Enable]
[30s]
[2]
Automatic Off Time
Brightness
Backlight Setting
Cancel OK
Enable/Disable
Cancel OK
Enable
Disable
When the [OK] is touched, the display returns to the
“Backlight Setting” screen.
NOTE
Whensetto“Disable”,[AutomaticO󰀨Time]and[Bright-
ness] setting are unnecessary.
(Cannot be set) Go to (8).
Setthetimeuntilbacklightisturnedo󰀨
(4) Touchthe[AutomaticO󰀨Time]onthe“BacklightSet-
ting” screen.
(5) “AutomaticO󰀨Time”screenisdisplayed.Selectthe[60
sec.] or [30 sec.].
(4) (5)
Enable/Disable [Enable]
[30s]
[2]
Automatic Off Time
Brightness
Backlight Setting
Cancel OK
Automatic Off Time
Cancel OK
30s
60s
When the [OK] is touched, the display returns to the
“Backlight Setting” screen.
AdjustthebrightnessofBacklight
(6) Touch the [Brightness] on the “Backlight Setting” screen.
(7) “Brightness” screen is displayed. Adjust the brightness
with the [
] or [ ].
(6) (7)
Enable/Disable [Enable]
[30s]
[2]
Automatic Off Time
Brightness
Backlight Setting
Cancel OK
2
3
1
Brightness
Cancel OK
Brightness
Cancel OK
When the [OK] is touched, the display returns to the
“Backlight Setting” screen.
Applythesetting
(8) After setting is complete,
touch the [OK] on the “Back-
light Setting” screen.
After the setting change is
displayed, the display returns
to the “Preference” screen.
Enable/Disable [Enable]
[30s]
[2]
Automatic Off Time
Brightness
Backlight Setting
Cancel OK
3-8-3 Contrast Setting
(1) Touch the [Contrast Setting] on the “Preference” screen.
(2) “Contrast Setting” screen is displayed. Adjust the con-
trast with [
] or [ ].
(1) (2)
Back
Preference
Panel
Calibration
Backlight
Setting
Contrast
2
3
4
5
1
Contrast
Cancel OK
When the [OK] is touched, after the setting change
screen is displayed, the display returns to the “Prefer-
ence” screen.
3-9 Initial Setting (for administrator)
Perform this setting at installation. The setting can also be
changed after installation.
(1) Touch the [Initial Setting] on the “Main Menu” screen.
(2) When“PasswordVerication”screenisdisplayed,enter
the Password (or Installer Password) and touch [OK].
(1) (2)
Monitor
Previous
Page
Page 2/ 3 Main Menu
Summer Time
Setting
Initial SettingPreference
Special Setting
Next
Page
0
CL
5
1
6
2
7
3
8
4
9
Cancel OK
Password Verification
Enter Current Password
(3) If the password is entered correctly, the “Initial Setting”
screen is displayed. The screen has 3 pages which are
switched by touching the [Next Page] or [Previous Page].
Back
Next
Page
Page 1/ 3 Initial Setting
Language Setting Date Setting
R.C.Group
Name Setting
Temp. Unit
Setting
Back
Previous
Page
Page 2/ 3 Initial Setting
R.C. Sensor
Setting
Password Setting
Display Item
Setting
Master Indoor
Unit Setting
Next
Page
Back
Previous
Page
Page 3/ 3 Initial Setting
R.C. Master/
Slave Setting
Lead Lag
Setting
I.U. Display
Number Setting
Thefollowingcontentsareset.(♦:forinstaller)
(*:Itemsthatindoorunitdoesnotsupportarenotdis-
played.)
• LanguageSetting:
The displayed language is switched. The displayable
languages are English (factory setting), French, Ger-
man, Spanish, Polish, Russian, Italian, Greek, Portu-
guese, Turkish, and Dutch.
• DateSetting:
The date and time display format are set. When the
poweristurnedo󰀨,thedateandtimedataholdtime
by built-in battery is approximately 7 days. When the
poweristurnedo󰀨forlongerthanthis,thedateand
time must be reset.
• Temp.UnitSetting:
The temperature display unit is switched to “°C” or “°F”.
Factory settings is “°C”.
• R.C.GroupNameSetting:
The remote controller group name can be set or
changed.
En-17