EasyManua.ls Logo

GE Interlogix 60-792-01-95R - Assigning the Latchkey Report Attribute; Setting the Time and Date; Adjusting System Sounds and Touchpad Brightness; Arming Your System Silently

GE Interlogix 60-792-01-95R
68 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Concord
16
Assigning the Latchkey Report Attribute
Latchkey Report is a user code attribute that causes the panel to send a message to a pager when
the user changes system arming levels. See “Latchkey Paging.
¾
To assign Latchkey Report to a user:
1. Enter the programming menus by pressing 9 + System or Partition Master CODE.
2. Press
030 nnn 5 where nnn is user 000 through 229.
3. To turn Latchkey Report:
on, press
2 + #.
off, press
1 + #.
4. Press
* + 00 + # to exit the programming menus.
Setting the Time
and Date
Although the installer usually sets the time and date at the time of installation, the user can
change it when necessary.
¾
To set the System Time:
1. Enter the programming menus by pressing 9 + System or Partition Master CODE.
2. Press
020.
3. Enter the correct time in 24-hour format (4 digits--see Figure 6), then press
#.
For example, if the current time is 7:23 a.m., press
0723 + #.
4. Press
* + 00 + # to exit the programming menus.
Figure 6. 24-Hour Format
¾ To set the System Date:
1. Enter the programming menus by pressing 9 + System or Partition Master CODE.
2. Press
021.
3. Enter the current date as 6 digits (mm/dd/yy) then press
#.
For example, if the current date is January 15, 2000, press
011500 + #.
4. Press
* + 00 + # to exit the programming menus.
Adjusting
System Sounds
and Touchpad
Brightness
Arming Your System Silently
Use the Silent Arming feature to arm your system without disturbing people throughout the
house with arming status beeps. There are two methods for implementing Silent Arming:
Silent on Demand. (User presses
5 before arming.)
Arming Always Silent (Silent Arming feature on).
Regardless of the method employed, when Silent Arming is in effect, no Exit beeps sound.
0 0 : 0 0
0 1 : 0 0
0 2 : 0 0
0 3 : 0 0
0 4 : 0 0
0 5 : 0 0
0 6 : 0 0
0 7 : 0 0
2 4 - H o u r F o r m a t
0 8 : 0 0
0 9 : 0 0
1 0 : 0 0
1 1 : 0 0
1 2 : 0 0
1 3 : 0 0
1 4 : 0 0
1 5 : 0 0
8 : 0 0 a m
9 : 0 0 a m
1 0 : 0 0 a m
1 1 : 0 0 a m
N o o n
1 : 0 0 p m
2 : 0 0 p m
3 : 0 0
p
m
1 6 : 0 0
1 7 : 0 0
1 8 : 0 0
1 9 : 0 0
2 0 : 0 0
2 1 : 0 0
2 2 : 0 0
2 3 : 5 9
4 : 0 0 p m
5 : 0 0 p m
6 : 0 0 p m
7 : 0 0 p m
8 : 0 0 p m
9 : 0 0 p m
1 0 : 0 0 p m
1 1 : 5 9
p
m
M i d n i g h t
1 : 0 0 a m
2 : 0 0 a m
3 : 0 0 a m
4 : 0 0 a m
5 : 0 0 a m
6 : 0 0 a m
7 : 0 0 a m

Table of Contents

Other manuals for GE Interlogix 60-792-01-95R

Related product manuals