EasyManua.ls Logo

GE NX-148E - Security NetworX LCD Keypad User Manual

GE NX-148E - Security NetworX LCD Keypad
32 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #17 background image
NX148E-CF
15
CHANGING USER CODES
Step 1 Press r 5 . The LCD Screen will prompt for a code.
Step 2 Enter [master code]. The LCD Screen will prompt for a user number.
NOTE: For partitioned systems, if you are changing the code of
another person, you must have access to all partitions, or at least
all of the partitions to which the other person has access.
Step 3 Enter the 2-digit user number. Always use leading zeros when
necessary, i.e. "04" for user number 4.
The LCD keypad will display the current code for this user. Stars (r)
represent blanks. NOTE: To delete
a user code, press [r]-[r]-[r]-[r]
for a 4-digit code or [r]-[r]-[r]-[r]-[r]-[r] for a 6-digit code.
Step 4 Enter the new user code for that individual. If you are changing the
current code, you may use the up and down scroll keys to select the digit
to change and enter the correct number. If it rejects the code because of
duplication or such, the sounder will beep 3 times.
Step 5 If another user code needs to be programmed, return to step 3 and enter
the user code.
Step 6 Press # while the LCD screen is prompting for a new user to exit
Code Programming,
ASSIGNING USER CODE AUTHORITY LEVELS
Assign authority levels to users by following the steps below. Assign user codes
before assigning authority levels.
NOTE: You must have authority to the partition you wish to add or remove
from another person’s authority.
Step 1 Press r 6 . The LCD Screen will now prompt for a code.
Step 2 Enter [master code]. The LCD Screen will prompt for a user number.
Step 3 Enter the 2-digit user number. Always use leading zeros when
necessary, i.e. "04" for user number 4. The LCD will now prompt you for
the attributes in the following chart.
Question and Answer IconNeed help?

Do you have a question about the GE NX-148E - Security NetworX LCD Keypad and is the answer not in the manual?

GE NX-148E - Security NetworX LCD Keypad Specifications

General IconGeneral
BrandGE
ModelNX-148E - Security NetworX LCD Keypad
CategoryKeypad
LanguageEnglish

Summary

Glossary of Terms

Abort Delay

Defines the option for a delay in reporting to the central station.

Authority Level

Defines the access level an individual has when using an alarm panel.

Central Station

Defines the location where alarm data is sent during an alarm report.

Chime Feature

Defines the option for the keypad to sound a ding-dong for entry/exit doors.

Codes

Explains user codes and function codes for turning specific functions on/off.

Duress Code

Defines a special code sent to indicate the system is operated under duress.

Forced Arming

Defines arming the system with open zones, indicated by a flashing ready light.

Function Code

Defines a code programmed by the installer to operate a device.

Group Bypass

Defines the option to bypass multiple zones with a single operation.

Instant/Delay

Defines alarm conditions for entry/exit doors with or without a delay.

Master Code

Defines a code that can program other user codes for arm/disarm.

Partitioned System

Defines a system divided into multiple areas controlled by users.

Perimeter

Defines the outer edge of the protected area.

Quick Arm

Defines arming the system using STAY or EXIT keys.

User Code

Defines a 4- or 6-digit code used to arm or disarm the system.

Understanding the Lights

Armed Light

Indicates if the system is armed or disarmed, and flashes after an alarm.

Bypass Light

Indicates when any zone in the keypad's partition is bypassed.

Cancel Light

Flashes during abort delay; indicates a cancel report is being processed.

Chime Light

Indicates when the chime feature is turned on.

Exit Light

Indicates during the exit delay, flashing in the last 10 seconds.

Fire Light

Steady for a fire zone fault, flashing for a fire zone trouble condition.

Power Light

Indicates primary power is on; flashes for a low battery condition.

Ready Light

Indicates the system is ready to arm or force arm.

Stay Light

Illuminates when all interior zones are bypassed.

Instant Message

LCD display indicating entry/exit doors have no delay.

Keypad Functions

Arming and Disarming Procedures

Covers arming the system in Away/Stay modes, quick arm, and disarming.

Zone Management and Bypass

Details on making the system ready, bypassing zones, group bypass, and unbypassing.

Emergency and System Operations

Using emergency activation keys and navigating the function menu.

Keypad and System Settings

Managing zone status, keypad tones, alarm memory, and system tests.

User and Device Configuration

Display tests, language changes, user code management, and X-10 device control.

System Maintenance and Logging

Resetting functions, viewing event logs, and adjusting LCD properties.

Clock and Chime Features

Setting the system clock and using the door chime feature.

Partitioned Systems Operation

Lights In Partitioning Master Mode

Explains the meaning of keypad lights when operating in master mode.

Displays In The Partitioning Master Mode

Describes how partition status is displayed in master mode.

Arming and Disarming Multiple Partitions

Steps for arming and disarming multiple partitions simultaneously.

Operating Individual Areas in the Multi-Partition Mode

How to operate specific partitions as if they were a single keypad.

Silencing Alarms in the Multi-Partition Mode

Procedure to silence alarms when the system is partitioned.

Keypad Control Tones (Beeps)

Service Display

Appendix A - Event Log

Emergency Evacuation Plans

System Notes

Related product manuals