i-24 Vivid E80/E90/E95 – Service Manual
GC091052
Rev. 3
Air Flow control
Air Flow components- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-22
Software control - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-22
Location- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-23
Casters and brakes
Casters and brakes description - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-24
Front End Processor (FEP)
Front End Card Rack general description - - - - - - - - - - - - - - - - - - - - - 5-25
Transmitter board (GTX) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-26
Relay board (GRLY) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-28
CRX board- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-30
Front Plane boards (XD BUS) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-32
cSound Power Module (CPM) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-33
Back End Processor (BEP)
Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-34
Signal flow and processing - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-34
Location of the Back End Processor (BEP) - - - - - - - - - - - - - - - - - - - - 5-34
BEP description - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-34
BEP’s side connectors - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-35
BEP’s top connectors - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-36
BEP’s rear connectors- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-36
Inside the BEP - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-36
LEDs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-37
BEP Power Supply - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-38
Graphics adapters - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-38
Internal storage devices - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-38
Power distribution
Main Power Supply- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-39
cSound Power Module (CPM) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-42
Input and Output (I/O) modules
Patient I/O (Physio)- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-43
BEP I/O Board - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-45
Restart Vivid E80/E90/E95 after diagnostics
Chapter 6 — Service Adjustments
LCD Monitor adjustments
Cautions and Warnings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-2
LCD backlight adjustment - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-3
Chapter 7 — Diagnostics/Troubleshooting
Service safety considerations
Gathering Troubleshooting Data
Purpose of this section - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
Collect Vital System Information- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
Collect a ‘trouble image’ with logs- - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-4
Screen captures
Purpose of this section - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-6
Ctrl+PrintScreen shortcut - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-6
Capture a screen image using the shortcut - - - - - - - - - - - - - - - - - - - - - 7-7