• CFG
• Ser
par
SER.P Serial protocol
0 CENCAL GEFRAN
1 MODBUS RTU
h.pb
h.it
h.dt
h.p.x
h.p.l
c.sp
c.pb
c.it
c.dt
c.p.x
c.p.l
rst
P.rs
A.rs
ffd
sof
Xy.i
Xy.2
Xy.3
xb.t
lb.t
lb.p
fa.p
g.sp
Proportional band for
heating or hysteresis in
regulation ON/OFF
Integral time for heating
Derivative time for
heating
Maximum power limit for
heating
Setpoint for cooling
relative to heating
setpoint
Proportional band for
coolingor hysteresis in
regulation ON/OFF
Integral time for cooling
Derivative time for
cooling
Maximum power limit for
cooling
Manual reset
Alarm 2 hysteresis
Alarm 3 hysteresis
Waiting time for HB alarm
intervention
Waiting time for LBA alarm intervention
(Set to “0” to disable LBA alarm)
Power limit for LBA
alarm condition
Power output in fault condition
(when probe is faulty)
0.00 ... 99.99 min
0.00 ... 99.99 min
0.0 ... 100.0%
-999 ... 999
scale points
0 ... 999.9%
full scale
0.00 ... 99.99 min
0.00 ... 99.99 min
0.0 ... 100.0%
Minimum power limit
for heating
(not available for double heat/
cool action)
0.0 ... 100.0%
± 25.0%
full scale
0 ... 999.9% f.s.
0 ... 999
secondos
0.0 ... 500.0 min
-100.0 ... 100.0%
-100.0 ... 100.0%
ON / OFF
Set gradient
(see applicable note)
0.0...999.9 digit/min.
(digit / sec see SP.r)
Antireset
Feedforward
0 ... 9999
scale points
-100.0 ... 100.0%
Reset power -100.0 ... 100.0%
Alarm 1 hysteresis
0…999 sec
If +32 in A1.t
0…999 min
If +64 in A1.t
0…999 sec
If +32 in A1.t
0…999 min
If +64 in A1.t
0…999 sec
If +32 in A1.t
0…999 min
If +64 in A1.t
Softstart time 0.0 ... 500.0 min
(Value has to be higher than cycle time value of
output to which HB alarm is assigned)
Cooling medium
0 ... 2
C.MEd Relative gain (Rg)
(see applicable note)
0 Air 1
1 Oil 0,8
2 Water 0,4
Minimum power limit for
cooling (not available for
heating/cooling double
action)
0.0 ... 100.0%
(.ME
-
(od
sr.p
Ser
Unit identification code
Serial setting
Serial interface
protocol
0 ... 9999
bav
Select
Baudrate
Parity selection
_ PAr Parity
0 No parity
1 Odd
2 Even
(*)
(*)
(*) LBA alarm may be reset by simultaneously pressing Δ + ∇ keys when OutP is displayed or by
switching to Manual.
Nota:
C_Pb, c_it, c_dt parameters are “read only” if the option “relative gain heat/cool control” (Ctrl = 14) has
been selected.
bAud Baudrate
0 1200
1 2400
2 4800
3 9600
4 19200
±999 scale points
±999 scale points
±999 scale points
S.tv
CFG
Control parameters
(*) +16 with passage automatic rifle in GO if
PV-SP > 0,5%
+32 with passage automatic rifle in GO if
PV-SP > 1%
+64 with passage automatic rifle in GO if
PV-SP > 2%
+128 with passage automatic rifle in GO if
PV-SP > 4%
Enabling
self-tuning,
autotuning,
softstart
S.tun Continuous Sel-ftuning Softstart
autotuning
0 NO NO NO
1 YES NO NO
2 NO YES NO
3 YES YES NO
4 NO NO YES
5 YES NO YES
6 - - -
7 - - -
S.tun Autotuning Selftuning Softstart
one shot
8* WAIT NO NO
9 GO NO NO
10* WAIT YES NO
11 GO YES NO
12* WAIT NO YES
13 GO NO YES
Nelle scale
tempi
0-999sec/
0-999min
non ha
significato
la presenza
del punto
decimale
(per dP.S
diverso
da 0)
580336L_MHW_600_07-2011_ENG
5 / 31
To Next Page
Loading...
Need help?
General
