To Next PageTo Next Page
Need help?Do you have a question about the Genie INTELLIG 1000 3024 and is the answer not in the manual?
General| Type | Chain Drive |
|---|---|
| Drive System | Chain |
| Warranty | Limited lifetime on motor, 1 year on parts |
| Battery Backup | No |
| Remote Control | 3-button remote |
| Smart Home Compatibility | Yes, with Aladdin Connect |
| Voltage | 120V |
| Speed | 7 inches per second |
| Security | Rolling code technology |
General safety information and overview of potential hazards.
Explains safety alert symbols and signal words used in the manual.
Key safety instructions to be followed and saved for future reference.
Describes the encryption system for door opener security.
Explains operation of the door opener from the inside garage.
Information on compatibility with vehicle home link systems.
Details the infrared safety beam system for door reversal.
Explains automatic door reversal upon contact with an object.
Describes automatic setting of minimum force for door operation.
Monitors Safe-T-Beam® system for proper functionality.
Details the two-bulb lighting system for safety and convenience.
Explains manual release of the door opener during power failure.
Instructions for adjusting programming for speed and force.
Steps for adjusting programming for speed, limits, and remotes.
Describes motion detection feature for automatic lighting.
Crucial warnings for reducing risk of severe injury or death during installation.
Explains how the infrared safety beam functions during door operation.
Lists requirements like wall console and safety system installation.
Lists required mechanical assembly tasks before proceeding with installation.
Guide on setting and testing door limits and force.
Steps for setting the close door travel limit.
Steps for setting the open door travel limit.
Instructions on setting the door opener's force.
Safety warnings related to door opener programming and operation.
Confirmation that basic power head programming is finished.
Steps for programming Homelink or Car2U systems.
Procedures for programming IntelliCode 1 remotes or wireless keypads.
Explains how remote LED colors indicate transmitting mode.
Step for selecting a remote button for programming.
Step to initiate programming by holding the remote button.
Procedure to switch between IntelliCode modes.
Step to confirm the IntelliCode mode selection.
Instructions for programming to older Genie openers.
Requirement for licensed electrician for direct power wiring.
Details about the typical support bracket not included with the opener.
Information on the optional header bracket mounting board.
Installation note for low headroom situations regarding door arms.
Requirement for licensed electrician for direct power wiring.
Details about the typical support bracket not included with the opener.
Information on the header bracket mounting board.
Warning about using the opener only with specific door types.
Details about the retail rail assembly.
Information on the professional installer rail.
Assembly details for one-piece and sectional doors.
Important note regarding the use of provided wall console and safety sensors.
Overview of the power head's four programming menus.
Identifies the location of programming buttons and LEDs on the power head.
Explanation of button functions and LED indicators during setup.
Details on button names, shapes, and their use.
Explanation of LED color meanings and displays.
General safety warnings for operating the door opener.
Images of different remote models.
Compliance information for FCC and IC certifications.
Details on the panic button feature for added security.
Information on dual IntelliCode compatibility.
Important note about remote compatibility.
Guide to best IntelliCode programming based on opener type.
Explains how remote LED colors indicate transmitting mode.
Step for selecting a remote button for programming.
Step to initiate programming by holding the remote button.
Procedure to switch between IntelliCode modes.
Step to confirm the IntelliCode mode selection.
Instructions for programming to older Genie openers.
Instruction to follow specific steps for re-entering remotes.
Compliance statement regarding US and Canadian legal requirements.
Critical safety warnings for reducing risk of injury or death.
Tasks for basic monthly maintenance of the opener.
Procedure for checking door balance and spring tension.
Warning about garage door hardware under pressure.
Warning about using only the supplied wall console.
Steps for checking the Safe-T-Beam® system status.
Procedure for testing the contact reverse function.
Steps for adjusting the door opener if it doesn't reverse correctly.
Note on automatic closing requiring Safe-T-Beam and programmed limits.
Explanation of carriage status based on red block indicator.
Description of the wall console indicator light behavior.
Function of the Open/Close button on the wall console.
Operation of the button to control power head lights.
How to activate and deactivate the vacation lock feature.
Troubleshooting tip for wall console operation issues.
Safety warning for changing light bulbs.
Step to disconnect power before changing bulbs.
Step to reconnect power and test operation.
Information on installing an optional dual wall console.
Safety warning regarding chain or belt tension adjustment.
Recommendation for annual visual inspection of chain or belt.
Instructions for adjusting belt tension.
Instructions for adjusting chain tension.
Procedure for replacing the remote's coin cell battery.
Wiring diagram for the opener circuit, for reference only.
Warning about electric shock hazard when opening the cover.
Diagram showing power cord connections.
Diagram showing connector and printed circuit board.
Guide for adjusting power head speed settings.
Note on speed settings for one-piece doors.
Table showing speed levels and corresponding LED indicators.
Guide for adjusting power head force settings.
Caution regarding door closing force adjustment.
Table showing force levels and corresponding LED indicators.
Table listing common operational problems and their solutions.
Troubleshooting steps for unintended opener activation.
Troubleshooting steps for noisy opener operation.
Troubleshooting steps for slow opener operation.
Continued list of operational problems.
Continued list of solutions for operational problems.
Table listing possible problems indicated by LED status.
Table providing solutions for LED error indications.
Warranty details for the motor/gearbox.
Warranty details for the belt.
Warranty details for other parts and accessories.
Section for purchaser's information.
