To Next PageTo Next PageWhat to do if my GGP Lawn Mower engine stops?
If your GGP Lawn Mower engine stops, turn the ignition key to the «STOP» position and check the following: the connections of the microswitches, recharge the battery, battery connections and the engine earth connection. The electronic circuit board might be blocked due to disconnected earth connections of the microswitches, a flat battery, a badly connected battery, or a badly earthed engine.
Why is my GGP MJ 66 Lawn Mower starting difficult or running erratically?
If your GGP Lawn Mower is hard to start or runs erratically, it could be due to a fault in carburetion. Try the following: clean or replace the air filter, flush out the float chamber, empty the fuel tank and refill it with fresh fuel, and check or replace the fuel filter.
What to do if my GGP MJ 66 has weak engine performance during cutting?
If your GGP Lawn Mower shows weak engine performance while cutting, it might be because the forward speed is too high relative to the cutting height. Reduce the forward speed and/or raise the cutting height.
What to do if my GGP MJ 66 has uneven mowing and poor grass collection?
If you experience uneven mowing and poor grass collection with your GGP Lawn Mower, check the tire pressure and reinstate the alignment of the cutting-means assembly in relation to the ground. Also, reduce the forward speed and/or raise the cutting-means assembly, wait for the grass to dry, remove the grass catcher and empty the collector channel, and clean the cutting-means assembly. This can happen if the cutting-means assembly is not parallel to the ground, the cutting means are inefficient, the forward speed is too high, the collector channel is blocked or the cutting-means assembly is full of grass.
What to do if my GGP MJ 66 Lawn Mower does not move when the drive pedal is pressed?
If your GGP Lawn Mower does not move when the drive pedal is pressed, ensure the release lever is in position «A» and not «B».
Why does my GGP MJ 66 Lawn Mower engine switch off when the cutting device is engaged?
If your GGP Lawn Mower engine switches off when engaging the cutting device, it might be because the lever movement is too abrupt or you are not ready to engage the cutting means. Try engaging it more slowly and ensure all safety requirements are met.
What to do if my GGP Lawn Mower has unusual vibrations while working?
If your GGP Lawn Mower experiences unusual vibrations while working, check and tighten all the engine and frame bolts. The vibrations might be caused by unbalanced cutting means, loose cutting means, or loose bolts and screws.
What to do if with the key on START the starter motor of my GGP Lawn Mower does not run?
If the starter motor on your GGP Lawn Mower doesn't run when the key is on «START», turn the ignition key to «STOP» and check the following: recharge the battery, replace the fuse (10 A), check connections of black earth leads, check earth connections, and ensure starting conditions are met. The electronic circuit board might be blocked due to a flat battery, blown fuse, bad earthing to the engine or frame, disconnected microswitch earth connections, a badly earthed starter motor, or unmet starting conditions.
General| Brand | GGP |
|---|---|
| Model | MJ 66 |
| Category | Lawn Mower |
| Language | English |
Read instructions carefully, become acquainted with controls, learn to stop engine quickly.
Ride-on lawnmower with seated operator, engine-driven cutting unit and transmission.
Machine usage requires care and attention; respect labels and precautions.
Lever to secure the machine when parked.
Lever to engage/disengage the cutting means, with automatic braking.
Pedal to engage reverse with cutting means engaged.
Acts as clutch for wheels and rear brake.
Pedal for braking the rear wheels.
General safety advice for operation, especially on slopes.
Explains how safety devices prevent starting or stop the engine.
Checks and operations before mowing for efficient and safe work.
Instructions for checking oil and refueling the machine safely.
Step-by-step guide for starting the engine.
Steps for starting cutting, including speed and height adjustments.
Safety precautions and limits for operating on slopes.
Warnings regarding malfunctions and when to contact a dealer.
Table summarizing maintenance tasks and frequencies.
