Why is there residue leaking from the hub of my Globe SP40 Mixer?
Residue leaking from the hub is caused by a contaminated hub due to build-up of meat and/or vegetable juices (especially tomatoes). To avoid this problem, always wipe the hub and dry it after each use. Note that acid from tomato juices will corrode/contaminate interior parts, so avoid mixing tomatoes in a meat grinder!
What if the display is not lit on Globe Mixer?
If the display is not lit, it may be due to no power to the unit. Check the power connections.
Why are the whip wires broken on my Globe Mixer?
Broken whip wires can occur if: * The batch size is too large for the mixer. Reduce the batch size and adjust the recipe. * The mixture is too firm, or the speed is too high. Reduce the speed. * A hand utensil was dropped into the bowl while mixing. Always stop the mixer before working on the mixture.
What to do if bowl raise sticking or not operational on Globe SP40?
If the bowl raise mechanism is sticking or not operational, it is likely due to a lack of lubrication on the bowl slides. Lubricate the bowl slides with mineral oil or food quality grease.
How to attach agitators easily onto the planetary shaft of Globe SP40?
If the agitators are difficult to attach to the planetary shaft, it may be due to a lack of lubrication or cleaning of the shaft. Wipe the planetary shaft with a clean damp cloth and lubricate it with mineral oil or food quality grease.
What to do if my Globe Mixer stops during mixing?
If your Globe Mixer stops during mixing, it could be due to a few reasons. First, the internal overload might have tripped. For SP25 and smaller models, press the stop button, then the reset button. For larger models, wait two minutes, press the stop button, then the start button. If the overload continues to trip, consider reducing the batch size or adjusting the recipe. Another cause could be a damaged or broken transmission belt, in which case you should contact a technician to replace the belt, applicable for SP25 and larger models. Lastly, if you have an SP80PL model, ensure you're not changing speeds during mixing; return the speed control lever to a speed model position and restart the mixer.
Why Globe SP40 Mixer will not mix medium or heavy loads?
Your Globe Mixer might struggle with medium or heavy loads if there is incorrect or low voltage.
How to reduce noise from a Globe SP40?
If your Globe Mixer is making excessive noise, consider the following: * Ensure the mixer is installed on a level surface. Adjust the surface or relocate the mixer, and make sure the rubber feet are installed. * Check that the bowl is seated correctly and the clamps are in place. Ensure the bowl is seated into the bowl cradle correctly and bowl clamps are locked into place. * Verify the agitator is fitted properly. Remove and reattach the agitator into position properly. * Avoid overloading the bowl. Reduce batch size.
What to do if my Globe Mixer stops during the mixing cycle?
If your Globe Mixer stops during the mixing cycle, it could be due to a few reasons: * The internal overload might have tripped. For SP25 and smaller models, press the stop button, then the reset button on the back of the mixer. For larger models, wait two minutes, then press ‘Start’ to restart the mixer. Reduce batch size or adjust recipe if this continues to occur! * Speeds were changed during mixing, SP80PL only. Return speed control lever to a speed model position and restart the mixer.
What to do if one or more gears not working on my Globe SP40?
If one or more gears are not working on your Globe Mixer, it is likely due to a damaged or broken gear. A technician needs to replace the gear. Always stop the mixer before changing speeds!
General environmental, safety, and occupational health notices and precautions.
Provides visual indicators for personal safety and potential equipment damage warnings.
Procedures for unpacking the mixer upon receipt and handling damaged items.
Step-by-step guide for preparing and positioning the mixer.
Instructions for safely connecting the mixer to electrical power.
Guidance for connecting and verifying rotation of three-phase mixer units.
Warnings to ensure safe mixer operation and prevent injury.
Procedures for operating, removing, and attaching the bowl guard and bowl.
Installing agitators, adding ingredients, and starting the mixing process.
Starting the mixer, selecting speeds, and managing overload protection.
Instructions for safely installing and using mixer attachments.
Instructions for using Manual and Timer modes on SP62P/SP80PL digital controls.
Cautions for safe cleaning procedures, including electrical disconnection.
Key details required for expedited parts shipment, including model, part number, and serial number.
General| Manufacturer | Globe |
|---|---|
| Model | SP40 |
| Speeds | 3 |
| Frequency | 60 Hz |
| Capacity | 40 qt |
| Material | Stainless Steel |
To Next Page
