Glow-worm Energy7 Series - Checking the Product for Leak-Tightness

60 pages

To Next Page

To Previous Page

Troubleshooting 13

0020300877_01 Energy

Installation and maintenance instructions 41

13.7 Checking the product for leak-tightness

▶ Check that the product is leak-tight. (→ Page 34)

Main Page

Table of Contents2
Safety4
Intended Use4
Qualification4
General Safety Information4
Regulations (Directives, Laws, Standards)6
List of Relevant Standards for Great Britain and Ireland6
Guarantee and Customer Service7
Technical Data8
Notes on the Documentation10
Product Description 511
CE Marking11
Benchmark11
Information on the Data Plate11
Functional Elements12
Safety Devices12
Set-Up13
Unpacking the Product13
Checking the Scope of Delivery13
Dimensions13
Installation Site14
Minimum Clearances14
Air/Flue Pipe14
Using the Mounting Template19
Wall-Mounting the Product19
Removing/Installing the Front Casing19
Removing/Installing the Side Section20
Installation21
Preparing for Installation21
Flushing the Heating Installation for the First Time ("Cold")21
Checking the Gas Meter21
Checking the Gas Flow Rate21
Installing the Heating Pump22
Heating Water Supply in the Open Heating System22
Heating Water Supply in the Closed Heating System22
Connecting the Heating Flow and Heating Return23
Check Compliance with the Local Gas Group23
Gas Connection23
Connecting the Condensate Discharge Pipe23
Flue Installation25
Electrical Installation25
Operation29
Using Diagnostics Codes29
Displaying the Status Codes29
Using Check Programmes29
Start-Up30
Carrying out the Initial Start-Up30
Heating Water Supply in the Sealed Heating System30
Checking and Treating the Heating Water/Filling and Supplementary Water30
Filling the Condensate Trap31
Checking the Gas Type32
Checking the Factory Setting32
Avoiding Danger Arising from Insufficient Water Pressure32
Switching on the Product32
Filling the Heating Installation32
Checking the Gas Setting32
Thoroughly Flushing the Heating Installation ("Hot")34
Checking Leak-Tightness34
Checking the Heating Mode34
Adapting the Unit to the Heating Installation35
Burner Anti-Cycling Time35
11 Handing over to the End User35
12 Inspection and Maintenance36
Using Original Seals36
Observing Inspection and Maintenance Intervals36
Checking the CO₂ Content36
Setting the CO₂ Content36
Removing the Gas-Air Mixture Unit36
Cleaning the Heat Exchanger37
Checking the Burner37
Checking the Ignition Electrode37
Cleaning the Condensate Trap38
12.10 Installing the Gas-Air Mixture Unit38
12.11 Draining the Product38
Completing Inspection and Maintenance Work38
12.13 Checking the Product for Leak-Tightness38
13 Troubleshooting39
Eliminating Faults39
Calling up the Fault Memory39
Deleting the Fault Memory39
Resetting Parameters to Factory Settings39
Preparing the Repair Work39
Replacing Defective Components39
Checking the Product for Leak-Tightness41
14 Decommissioning the Product42
15 Recycling and Disposal42
Appendix43
A Inspection and Maintenance Work43
B Check Programmes - Overview44
C Overview of Diagnostics Codes45
D Status Codes - Overview47
E Overview of Fault Codes48
F Wiring Diagram50
G Wiring Diagram, 30 Kw51
H Commissioning Checklist52
Pipe Lengths for the Air/Flue Pipe56
Length of the C13 Type Air/Flue Pipe56
Length of the C33 Type Air/Flue Pipe56
Length of the C43 Type Air/Flue Pipe56
Index57

Glow-worm Energy7 Series - Checking the Product for Leak-Tightness

Table of Contents

Other manuals for Glow-worm Energy7 Series

Related product manuals