GME TX667 - Scanning Features and Behavior; Initiating and Controlling Channel Scans; Scan Mode Operation Details

TX667 Instruction Manual
24
SCANNING FOR CHANNELS
1. To scan for channels, briey press F followed by the  key. The
TX677 Instrucon Manual
12 June 2018
© 2018 Standard Communicaons Pty Ltd trading as GME. All rights reserved.
21
50157
Content
Factory Reset
A factory reset clears any sengs you have made to your radio, and restores it to the default factory
sengs.
To perform a factory reset, press and hold the Menu and SQL keys simultaneously while switching the
radio on.
Scanning
Channel scanning allows you to monitor all channels for incoming signals.
While the radio is scanning, the Menu seng key is disabled.
Adding or Removing Channels
To select channels for scanning:
Press the or keys to select the desired channel.
1. If the icon is visible, the selected channel is already in the Scan Memory.
Press F followed by SQL to remove the channel from the scan memory. A low beep will
be heard and the icon will disappear.
2. If the icon is not visible the selected channel is not presently in the
scan memory. Press F followed by SQL to add the channel to the scan memory.
Scanning for Channels
1. To scan for channels, briey press F followed by the key. The icon will ash and the
channel numbers will change as the radio scans through the channels.
2. To change the scan direcon while scanning, briey press the or keys.
3. To stop scanning, briey press F followed by the key. The icon will stop ashing and
the radio will return to normal operaon.
There must be at least 2 channels stored in the scan memory. If not, the radio will not scan.
icon will ash and the channel numbers will change as the
radio scans through the channels.
2. To change the scan direction while scanning, briey press the 
or  keys.
3. To stop scanning, briey press F followed by the  key. The
TX677 Instrucon Manual
12 June 2018
© 2018 Standard Communicaons Pty Ltd trading as GME. All rights reserved.
21
50157
Content
Factory Reset
A factory reset clears any sengs you have made to your radio, and restores it to the default factory
sengs.
To perform a factory reset, press and hold the Menu and SQL keys simultaneously while switching the
radio on.
Scanning
Channel scanning allows you to monitor all channels for incoming signals.
While the radio is scanning, the Menu seng key is disabled.
Adding or Removing Channels
To select channels for scanning:
Press the or keys to select the desired channel.
1. If the icon is visible, the selected channel is already in the Scan Memory.
Press F followed by SQL to remove the channel from the scan memory. A low beep will
be heard and the icon will disappear.
2. If the icon is not visible the selected channel is not presently in the
scan memory. Press F followed by SQL to add the channel to the scan memory.
Scanning for Channels
1. To scan for channels, briey press F followed by the key. The icon will ash and the
channel numbers will change as the radio scans through the channels.
2. To change the scan direcon while scanning, briey press the or keys.
3. To stop scanning, briey press F followed by the key. The icon will stop ashing and
the radio will return to normal operaon.
There must be at least 2 channels stored in the scan memory. If not, the radio will not scan.
icon will stop ashing and the radio will return to normal operation.
Note: There must be at least 2 channels stored in the scan memory. If not, the
radio will not scan.
SCANNING FEATURES
• If a signal is received, the scan is paused allowing you to transmit and
receive on that channel. During this time the
TX677 Instrucon Manual
12 June 2018
© 2018 Standard Communicaons Pty Ltd trading as GME. All rights reserved.
21
50157
Content
Factory Reset
A factory reset clears any sengs you have made to your radio, and restores it to the default factory
sengs.
To perform a factory reset, press and hold the Menu and SQL keys simultaneously while switching the
radio on.
Scanning
Channel scanning allows you to monitor all channels for incoming signals.
While the radio is scanning, the Menu seng key is disabled.
Adding or Removing Channels
To select channels for scanning:
Press the or keys to select the desired channel.
1. If the icon is visible, the selected channel is already in the Scan Memory.
Press F followed by SQL to remove the channel from the scan memory. A low beep will
be heard and the icon will disappear.
2. If the icon is not visible the selected channel is not presently in the
scan memory. Press F followed by SQL to add the channel to the scan memory.
Scanning for Channels
1. To scan for channels, briey press F followed by the key. The icon will ash and the
channel numbers will change as the radio scans through the channels.
2. To change the scan direcon while scanning, briey press the or keys.
3. To stop scanning, briey press F followed by the key. The icon will stop ashing and
the radio will return to normal operaon.
There must be at least 2 channels stored in the scan memory. If not, the radio will not scan.
icon will continue to
ash to show that the scan is still active. Once the channel has been
inactive for 5 seconds the scan will automatically resume.
• Pressing the PTT switch while the radio is scanning will jump to the
working channel allowing you to transmit and receive on that channel
(the working channel is the channel the radio was on at the time the
scan was activated). During this time the
TX677 Instrucon Manual
12 June 2018
© 2018 Standard Communicaons Pty Ltd trading as GME. All rights reserved.
21
50157
Content
Factory Reset
A factory reset clears any sengs you have made to your radio, and restores it to the default factory
sengs.
To perform a factory reset, press and hold the Menu and SQL keys simultaneously while switching the
radio on.
Scanning
Channel scanning allows you to monitor all channels for incoming signals.
While the radio is scanning, the Menu seng key is disabled.
Adding or Removing Channels
To select channels for scanning:
Press the or keys to select the desired channel.
1. If the icon is visible, the selected channel is already in the Scan Memory.
Press F followed by SQL to remove the channel from the scan memory. A low beep will
be heard and the icon will disappear.
2. If the icon is not visible the selected channel is not presently in the
scan memory. Press F followed by SQL to add the channel to the scan memory.
Scanning for Channels
1. To scan for channels, briey press F followed by the key. The icon will ash and the
channel numbers will change as the radio scans through the channels.
2. To change the scan direcon while scanning, briey press the or keys.
3. To stop scanning, briey press F followed by the key. The icon will stop ashing and
the radio will return to normal operaon.
There must be at least 2 channels stored in the scan memory. If not, the radio will not scan.
icon will continue to ash
to show that the scan is still active. Once the working channel has been
inactive for 5 seconds the scan will automatically resume.
• If the scan is paused on a busy channel that you don’t wish to listen
to, press the  or  keys to skip over the channel and continue
scanning.
Note: The Scan mode will reduce the overall battery life because the ‘Standby’
(battery saver) feature is overridden. If the battery is running low you should avoid
scanning to conserve power.