To Next PageTo Next PageHow to fix a Graco Husky 2150 that cycles at stall or fails to hold pressure?
If your Graco Water Pump cycles at stall or fails to hold pressure, it is likely due to worn check valve balls, seats, or o-rings. Replacing these components should resolve the issue.
How to fix air leaks on my Graco Water Pump?
External air leaks in your Graco Water Pump can be caused by loose air valve cover or air valve cover screws, a damaged air valve gasket or air cover gasket, or loose air cover screws. Try tightening the screws, or inspecting and replacing the gaskets.
Why are there air bubbles in the fluid from my Graco Husky 2150 Water Pump?
Air bubbles in the fluid can occur in your Graco Water Pump if the suction line is loose, a diaphragm has ruptured, the inlet manifold is loose, there is a damaged seal between the manifold and seat, damaged o-rings, or the fluid side diaphragm plate is loose. To resolve this, tighten the suction line, replace the diaphragm, tighten the manifold bolts, replace the seats or o-rings, or tighten/replace the fluid side diaphragm plate.
What to do if my Graco Husky 2150 operates erratically?
Erratic operation of your Graco Water Pump can stem from a clogged suction line, sticky or leaking balls, a ruptured diaphragm, or a restricted exhaust. You should inspect and clear any clogs in the suction line, clean or replace any sticky or leaking balls, replace the diaphragm, and remove any restrictions in the exhaust.
Why won't my Graco Husky 2150 Water Pump cycle, or why does it cycle once and stop?
If your Graco Water Pump won't cycle, or cycles once and stops, it could be due to a stuck or dirty air valve, a check valve ball that is severely worn and wedged in the seat or manifold, a check valve ball wedged into the seat due to overpressurization, or a clogged dispensing valve. Try disassembling and cleaning the air valve, replacing the ball and seat, installing a Pressure Relief Valve, or relieving pressure and clearing the dispensing valve.
How to stop fluid from coming out of the exhaust air of my Graco Husky 2150?
Fluid in the exhaust air of your Graco Water Pump is typically caused by a ruptured diaphragm or a loose fluid side diaphragm plate. Replace the diaphragm, or tighten/replace the fluid side diaphragm plate to fix this.
Why does my Graco Water Pump exhaust excessive air when stalled?
Excessive air exhaust at stall in your Graco Water Pump may be due to a worn air valve block, o-ring, plate, pilot block, u-cups, or pilot pin o-rings or worn shaft seals. Inspect and replace these components as needed.
Why is my Graco Husky 2150 leaking fluid externally from the ball check valves?
Fluid leaks from the ball check valves of your Graco Water Pump are often due to loose manifolds, a damaged seal between the manifold and seat, or damaged o-rings. Try tightening the manifold bolts or replacing the seats or o-rings.
What to do if there is fluid in exhaust air of Graco Husky 2150?
If you observe fluid in the exhaust air of your Graco Water Pump, it typically indicates a ruptured diaphragm, a loose diaphragm shaft bolt, or a damaged o-ring. You should replace the diaphragm, tighten or replace the diaphragm shaft bolt, or replace the damaged o-ring.
What to do if Graco Husky 2150 Water Pump will not cycle, or cycles once and stops?
If your Graco Water Pump will not cycle or cycles once and stops, several issues could be the cause. The air valve may be stuck or dirty, requiring disassembly and cleaning with filtered air. The check valve ball could be severely worn and wedged in the seat or manifold, necessitating replacement of both the ball and seat. Overpressurization could also wedge the check valve ball into the seat, in which case you should install a Pressure Relief Valve. Lastly, the dispensing valve might be clogged, requiring you to relieve pressure and clear the valve.
General| Type | Air-Operated Double Diaphragm Pump |
|---|---|
| Maximum Fluid Pressure | 125 psi (8.6 bar) |
| Non-Wetted Materials | Aluminum, Polypropylene |
| Air Pressure Operating Range | 20-125 psi (1.4-8.6 bar) |
| Max. Solid Size | 1/4 in (6.3 mm) |
| Power Source | Compressed Air |
| Air Inlet Size | 1/2 in npt(f) |
| Fluid Inlet Size | 2 in |
| Fluid Outlet Size | 2 in |
| Maximum Suction Lift | 30 ft (9.1 m) |
| Wetted Materials | Aluminum, Stainless Steel, Polypropylene |
| Hose Size | 2 in |
| Engine Type | Not Applicable |
| Engine Displacement | Not Applicable |
| Fuel Tank Capacity | Not Applicable |
