What to do if Graco LineLazer 130HS Construction Equipment fluid is spitting from gun?
If fluid is spitting from the gun, consider the following: * There might be air in the pump or hose: Check and tighten all fluid connections. Reprime the pump. * The tip might be partially clogged: Clear the tip. * The fluid supply might be low or empty: Refill the fluid supply. Prime the pump and check the fluid supply often to prevent running the pump dry.
Why Graco Construction Equipment engine won't start?
There are several reasons why your Graco Construction Equipment engine might not start: * The engine switch could be OFF: Turn the engine switch ON. * The engine could be out of gas: Refill the gas tank. * The engine oil level could be low: Replenish the oil. * The spark plug cable could be disconnected or damaged: Connect the spark plug cable or replace the spark plug. * The engine could be cold: Use the choke. * The fuel shutoff lever could be OFF: Move the lever to the ON position. * Oil could be seeping into the combustion chamber: Remove the spark plug, pull the starter 3 to 4 times, clean or replace the spark plug, and start the engine. Keep the sprayer upright to avoid oil seepage.
Why won't my Graco Paint Sprayer engine start?
If your Graco Paint Sprayer engine won’t start, there are several potential causes: * The engine switch may be OFF, in which case you should turn it ON. * The engine may be out of gas, so refill the gas tank. * The engine oil level may be low, so replenish the oil if necessary. * The spark plug cable may be disconnected or damaged, so connect or replace the spark plug. * If the engine is cold, use the choke. * The fuel shutoff lever may be OFF, so move it to the ON position. * Oil may be seeping into the combustion chamber; remove the spark plug, pull the starter 3 to 4 times, clean or replace the spark plug, and start the engine, keeping the sprayer upright to avoid oil seepage.
Why is there high engine speed at no load in my Graco Paint Sprayer?
If your Graco Paint Sprayer has high engine speed at no load, it may be due to: * A misadjusted throttle setting, so reset the throttle to 3700 -- 3800 engine rpm at no load. * A worn engine governor, so replace or service the engine governor.
Why is there low stall or run pressure shown on display of my Graco Paint Sprayer?
If your Graco Paint Sprayer shows a low stall or run pressure on the display, it could be due to: * A new pump or new packings, as the pump break-in period can take up to 100 gallons of material. * A faulty transducer, so replace it.
Why is there excessive hydraulic pump noise in my Graco Paint Sprayer?
If your Graco Paint Sprayer has excessive hydraulic pump noise, it is likely due to a low hydraulic fluid level. Shut off the sprayer and add fluid.
Why is the fluid delivery low on my Graco Paint Sprayer?
If the Graco Paint Sprayer fluid delivery is low, consider the following: * Increase the pressure setting. * Clean the displacement pump outlet filter if it's dirty or clogged. * Tighten the intake line to the pump inlet if it's not tight. * The hydraulic motor may be worn or damaged; bring the sprayer to a Graco distributor for repair. * If there's a large pressure drop in the fluid hose, use a larger diameter or shorter hose.
Why is my Graco Paint Sprayer overheating?
If the Graco Paint Sprayer is overheating, it could be due to: * Paint buildup on the hydraulic components, so clean them. * Low oil level, so fill it with oil.
What to do if Graco Paint Sprayer displacement pump operates, but output is low on up-stroke?
If your Graco Paint Sprayer's displacement pump operates, but the output is low on the up-stroke, it could be due to: * The piston ball not seating properly, so service the piston ball. * Worn or damaged piston packings, so replace the packings.
What to do if Graco Paint Sprayer engine operates, but displacement pump does not operate?
If your Graco Paint Sprayer engine operates, but the displacement pump does not, check the following: * Ensure the pump valve is ON. * Increase the pressure setting by turning the pressure adjusting knob clockwise. * Clean the fluid filter. * Clean the tip or tip filter if clogged. * If the displacement pump piston rod is stuck due to dried paint, repair the pump. * Replace the belt if it's worn, broken, or off the pulley. * Add hydraulic fluid if it's too low. * If the hydraulic motor is not shifting, set the pump valve to OFF, turn the pressure down, turn the engine OFF, and pry the rod up or down until the hydraulic motor shifts.
Highlights critical safety guidelines for operating the equipment.
Warns about risks of flammable fumes and static sparking during operation.
Details dangers of high-pressure spray injecting into the body, requiring immediate treatment.
Alerts users to the danger of poisonous carbon monoxide gas from exhaust.
Covers risks from fatigue, alcohol, exceeding pressure limits, and improper use.
Warns about chemical reactions with aluminum in pressurized systems causing rupture.
Highlights risks of pinching, cutting, or amputating from moving components.
Describes dangers from rotating parts and loose clothing during operation.
Warns about serious injury or death from exposure to toxic fluids or fumes.
Advises caution regarding hot equipment surfaces and fluids to avoid severe burns.
Addresses common problems like engine starting failures, pump not operating, or low output.
Covers difficulties with priming, fluid spitting, leakage, overheating, and noise.
General| Brand | Graco |
|---|---|
| Model | LineLazer 130HS |
| Category | Construction Equipment |
| Language | English |
To Next Page
