Graco LineLazer 130HS User Manual (English)

Other manuals for Graco LineLazer 130HS

Questions and Answers:

M
Melissa EspinozaAug 22, 2025
Why won't my Graco Paint Sprayer engine start?
- A
  Austin PalmerAug 22, 2025
  If your Graco Paint Sprayer engine won’t start, there are several potential causes: * The engine switch may be OFF, in which case you should turn it ON. * The engine may be out of gas, so refill the gas tank. * The engine oil level may be low, so replenish the oil if necessary. * The spark plug cable may be disconnected or damaged, so connect or replace the spark plug. * If the engine is cold, use the choke. * The fuel shutoff lever may be OFF, so move it to the ON position. * Oil may be seeping into the combustion chamber; remove the spark plug, pull the starter 3 to 4 times, clean or replace the spark plug, and start the engine, keeping the sprayer upright to avoid oil seepage.
R
rmartinAug 23, 2025
Why is my Graco Paint Sprayer spitting fluid?
- E
  Elizabeth MartinAug 25, 2025
  If your Graco Paint Sprayer is spitting fluid from the gun, it could be due to: * Air in the pump or hose. Check and tighten all fluid connections and re-prime the pump. * A partially clogged tip. Clear the tip. * A low or empty fluid supply. Refill the fluid supply and prime the pump. Check the fluid supply often to prevent running the pump dry.
C
Craig WilliamsAug 25, 2025
Why is there excessive paint leakage into throat packing nut of my Graco Paint Sprayer?
- N
  Nicholas CainAug 26, 2025
  If your Graco Paint Sprayer has excessive paint leakage into the throat packing nut, it could be because: * The throat packing nut is loose, so remove the throat packing nut spacer and tighten the nut just enough to stop the leakage. * The throat packings are worn or damaged, so replace them. * The displacement rod is worn or damaged, so replace the rod.
V
Victor MedinaAug 26, 2025
How to fix a Graco Paint Sprayer that pulls hard (won’t start)?
- J
  James JohnsonAug 27, 2025
  If the gas engine of your Graco Paint Sprayer pulls hard and won’t start, it's likely because the hydraulic pressure is too high. Turn the hydraulic pressure knob counterclockwise to the lowest setting.
K
kimberlyrushAug 28, 2025
What to do if Graco Paint Sprayer engine operates, but displacement pump does not operate?
- A
  Andrew AndersonAug 28, 2025
  If your Graco Paint Sprayer engine operates, but the displacement pump does not, check the following: * Ensure the pump valve is ON. * Increase the pressure setting by turning the pressure adjusting knob clockwise. * Clean the fluid filter. * Clean the tip or tip filter if clogged. * If the displacement pump piston rod is stuck due to dried paint, repair the pump. * Replace the belt if it's worn, broken, or off the pulley. * Add hydraulic fluid if it's too low. * If the hydraulic motor is not shifting, set the pump valve to OFF, turn the pressure down, turn the engine OFF, and pry the rod up or down until the hydraulic motor shifts.
L
Latasha ArnoldAug 30, 2025
What to do if Graco Paint Sprayer displacement pump operates, but output is low on up-stroke?
- D
  djamesAug 30, 2025
  If your Graco Paint Sprayer's displacement pump operates, but the output is low on the up-stroke, it could be due to: * The piston ball not seating properly, so service the piston ball. * Worn or damaged piston packings, so replace the packings.
K
Karla TownsendAug 31, 2025
Why is my Graco Paint Sprayer overheating?
- R
  Richard NealAug 31, 2025
  If the Graco Paint Sprayer is overheating, it could be due to: * Paint buildup on the hydraulic components, so clean them. * Low oil level, so fill it with oil.
S
Shawna LopezSep 1, 2025
Why is the fluid delivery low on my Graco Paint Sprayer?
- K
  Kathy LesterSep 1, 2025
  If the Graco Paint Sprayer fluid delivery is low, consider the following: * Increase the pressure setting. * Clean the displacement pump outlet filter if it's dirty or clogged. * Tighten the intake line to the pump inlet if it's not tight. * The hydraulic motor may be worn or damaged; bring the sprayer to a Graco distributor for repair. * If there's a large pressure drop in the fluid hose, use a larger diameter or shorter hose.
R
Robert LewisSep 2, 2025
Why is there excessive hydraulic pump noise in my Graco Paint Sprayer?
- R
  Ronald WoodSep 2, 2025
  If your Graco Paint Sprayer has excessive hydraulic pump noise, it is likely due to a low hydraulic fluid level. Shut off the sprayer and add fluid.
R
Raymond ArellanoSep 4, 2025
Why is there low stall or run pressure shown on display of my Graco Paint Sprayer?
- K
  Kathleen CarlsonSep 4, 2025
  If your Graco Paint Sprayer shows a low stall or run pressure on the display, it could be due to: * A new pump or new packings, as the pump break-in period can take up to 100 gallons of material. * A faulty transducer, so replace it.