Graco LineLazer ES 1000

Other manuals for Graco LineLazer ES 1000

Questions and Answers

J
Jackie WardAug 22, 2025
What to do if Graco LineLazer ES 1000 Construction Equipment sprayer does not run at all and control board status light blinks 6 times repeatedly?
- J
  Jason BarronAug 22, 2025
  If your Graco Construction Equipment sprayer isn't running and the control board light blinks six times, it indicates the motor is hot or there's a fault in the motor thermal device. First, allow the sprayer to cool down. If it runs when cool, ensure the sprayer is in a cooler, well-ventilated location and that the motor air intake isn't blocked. If it still doesn't run, replace the motor after checking the thermal device connector and its resistance. If replacing the motor doesn't solve the problem, replace the control board.
R
Robert MedinaAug 25, 2025
What to do if my Graco LineLazer ES 1000 sprayer does not run at all and the control board status light blinks 2 times repeatedly?
- P
  Patrick GomezAug 25, 2025
  If your Graco Construction Equipment sprayer isn't running and the control board status light blinks twice repeatedly, ensure there's no pressure in the system. Check the fluid path for clogs, like a clogged filter, and use an airless paint spray hose without metal braid to avoid high-pressure spikes. Turn the ON/OFF switch OFF, disconnect the power, and check the transducer and its connections to the control board for cleanliness and secure connection. If the issue persists, install a new transducer. If the sprayer still doesn't run, replace the control board.
R
rtaylorAug 26, 2025
What to do if my Graco Construction Equipment sprayer does not run at all and the control board status light blinks 3 times repeatedly?
- B
  beverlyharrisAug 26, 2025
  If your Graco Construction Equipment sprayer isn't running and the control board status light blinks three times repeatedly, it means the control board isn't detecting a pressure signal. Turn the sprayer OFF and disconnect the power. Check the transducer and its connections to the control board, ensuring they are clean and secure. If the sprayer still doesn't run, connect a confirmed working transducer. If it runs, install a new transducer; otherwise, replace the control board. Also, check the transducer resistance with an ohmmeter (less than 9k ohm between red and black wires and 3-6k ohm between green and yellow wires).
R
Ryan AyalaAug 29, 2025
Why is my Graco LineLazer ES 1000 leaking excessively into throat packing nut?
- B
  blairchristinaAug 30, 2025
  Excessive paint leakage into the throat packing nut of your Graco Construction Equipment may be caused by: A loose throat packing nut: Remove the throat packing nut spacer and tighten the nut just enough to stop the leakage. Worn or damaged throat packings: Replace the packings. A worn or damaged displacement rod: Replace the rod.
J
Jason WagnerAug 31, 2025
What to do if Graco Construction Equipment sprayer does not shut off and control board status light blinks 2 times repeatedly?
- L
  lthomasAug 31, 2025
  If your Graco Construction Equipment sprayer doesn't shut off and the control board status light blinks twice repeatedly, the control board needs to be replaced.
C
Carol GonzalezSep 2, 2025
Why is fluid spitting from my Graco Construction Equipment gun?
- H
  haley55Sep 2, 2025
  Fluid spitting from your Graco Construction Equipment gun can be due to: Air in the pump or hose: Check and tighten all fluid connections and cycle the pump slowly during priming. A partially clogged spray tip: Clear the tip. Low or empty fluid supply: Refill the fluid supply and prime the pump, checking the supply often to prevent running the pump dry.
K
Kristin WolfeSep 4, 2025
What causes a Graco Construction Equipment motor to run but the pump does not stroke?
- H
  Heather AndersonSep 4, 2025
  If the motor of your Graco Construction Equipment runs, but the pump doesn't stroke, it could be due to: A damaged connecting rod assembly: Replace the connecting rod assembly. Damaged gears or drive housing: Inspect the drive housing assembly and gears for damage and replace if necessary.
Y
yvettelloydSep 6, 2025
Why won't my Graco LineLazer ES 1000 battery stay charged?
- S
  Shelby TrevinoSep 6, 2025
  If your Graco Construction Equipment battery won’t stay charged, it may be because accessories are left on, draining the battery when the unit is not in use. Make sure to turn off accessories when the machine is not in use.
E
Eric MurphySep 7, 2025
Why is the AC output voltage low on my Graco LineLazer ES 1000 and the inverter turns loads OFF quickly?
- A
  Anthony WilliamsSep 7, 2025
  If the AC output voltage is low on your Graco Construction Equipment and the inverter turns loads OFF quickly, it's likely due to a low battery. Check the condition of the batteries and recharge them if possible.
J
Jessica JonesSep 9, 2025
What causes a Graco LineLazer ES 1000 charger to supply a lower charge rate?
- S
  sean95Sep 9, 2025
  A lower charge rate from your Graco Construction Equipment charger is caused by improperly set charger controls. Refer to the section on adjusting the “Charger Rate”.