To Next PageTo Next PageWhat to do if my Graco Super nova 495 has low output due to electric supply issues?
If you're experiencing low output with your Graco Paint Sprayer, with electric supply with volt meter, reset the building circuit breaker, replace the building fuse, or repair the electrical outlet or try another one.
How to fix electrical problems with my Graco Super nova 495 related to the extension cord?
If you're experiencing basic electrical problems with your Graco Paint Sprayer due to the extension cord, replace the extension cord.
What to do if the building circuit breaker opens when I turn on my Graco Paint Sprayer?
If the building circuit breaker opens as soon as you turn on your Graco Paint Sprayer, inspect all electrical wiring for damaged insulation and all terminals for loose fit or damage. Repair or replace any damaged wiring or terminals and securely reconnect all wires.
Why is the motor on my Graco Paint Sprayer hot and running intermittently?
If your Graco Paint Sprayer's motor is hot and runs intermittently, it might be due to operating at high pressure with small tips. Try decreasing the pressure setting or increasing the tip size.
What to do if the motor runs but the pump doesn't stroke on my Graco Paint Sprayer?
If the motor runs but the pump does not stroke on your Graco Paint Sprayer, it could be due to a damaged or missing displacement pump pin. Replace the pump pin if it's missing and ensure the retainer spring is fully in the groove all around the connecting rod.
What to do if my Graco Super nova 495 Paint Sprayer has low output because of a worn spray tip?
If you experience low output from your Graco Paint Sprayer, and suspect a worn spray tip, relieve the pressure and then replace the tip.
What to do if my Graco Paint Sprayer has low output and the filter is clogged?
If you're experiencing low output from your Graco Paint Sprayer, the filter may be clogged. Relieve the pressure and then check and clean the filter.
What to do if my Graco Super nova 495 Paint Sprayer has low output because of a leaking prime valve?
If you notice low output from your Graco Paint Sprayer, and the prime valve is leaking, relieve the pressure and repair the prime valve.
How to troubleshoot basic fluid pressure problems with my Graco Paint Sprayer?
If you have basic fluid pressure problems with your Graco Paint Sprayer, slowly increase the pressure to see if the motor starts. Alternatively, relieve the pressure and clear any clogs, or clean the filter.
What to do if the pump is frozen or paint hardened in my Graco Super nova 495 Paint Sprayer?
If you're having basic mechanical problems with your Graco Paint Sprayer, such as a pump frozen or paint hardened in the pump, thaw the sprayer if water or water-based paint has frozen inside by placing it in a warm area until completely thawed. Do not start the sprayer until it is fully thawed. If paint has hardened (dried) inside, replace the pump packings.
General| Brand | Graco |
|---|---|
| Model | Super nova 495 |
| Category | Paint Sprayer |
| Language | English |
Describes the product line for architectural paints and coatings.
Highlights critical safety warnings and instructions for manual use.
Details risks associated with flammable fumes and ignition sources during operation.
Outlines dangers of improper grounding, setup, and usage leading to electric shock.
Warns about high-pressure fluid injection injuries and necessary precautions.
Highlights dangers of improper use, modification, and operation of the equipment.
Details risks from exposure to hazardous fluids and fumes, requiring MSDS review.
Specifies essential PPE required for safe operation, servicing, and area presence.
Diagram and list identifying all major sprayer parts and their functions.
Details the necessity of grounding, plug requirements, and safe electrical connections.
Specifies voltage, amperage needs, and guidelines for using extension cords.
Provides instructions for using pails and grounding during pressure relief.
Details the procedure to safely relieve pressure, including handling clogs.
Instructions for connecting hoses, tightening fittings, and removing the tip guard.
Details inlet strainer check, packing nut lubrication, and power connection.
Guides on setting pressure, circulating fluid, and priming the system.
Instructions for assembling the spray tip and guard onto the gun.
Procedures for flushing the system and transitioning from flushing fluid to paint.
Guidance on testing spray patterns and adjusting pressure for optimal results.
Step-by-step instructions for safely clearing blockages in the spray tip.
Covers powering off, relieving pressure, and preparing for flushing.
Details on flushing the system with appropriate fluids and rinsing.
Instructions for plugging in and turning on the sprayer with a digital display.
How to change displayed pressure units between psi, bar, and MPa.
Steps to enter and navigate stored data, including model and runtime information.
How to view error codes, software revisions, and erase error data.
Navigating the main menu for pressure display and job data.
Accessing secondary menu options like error codes and software revision.
Procedure to switch between psi, bar, and MPa, affecting gallon/liter display.
Instructions on how to clear error codes and reset the system.
