Graco XP-H Series User Manual (English)

Other manuals for Graco XP-H Series

Questions and Answers:

G
Gina RobinsonAug 22, 2025
Why does my Graco Paint Sprayer system stop or not start?
- A
  Angela JacksonAug 22, 2025
  If your Graco Paint Sprayer system stops or won't start, it could be due to several reasons. The air pressure or volume might be too low, so increase it and check the air compressor. The air line or air valve could be closed or restricted, so open or clean them. Ensure that the fluid valves are open. A clogged fluid hose could also be the issue, in which case you should replace it. If the air motor is worn or damaged, repair it. Finally, a stuck displacement pump can cause this problem; in this case, repair the pump.
J
jacobcostaAug 23, 2025
What to do if relief valve leaks on Graco Paint Sprayer?
- R
  robert12Aug 23, 2025
  If the relief valve on your Graco Paint Sprayer leaks back to the supply, opens too soon, or won't close, it indicates that the relief valve is either dirty or damaged. Replace the over pressure relief valve.
M
Marc StevensAug 25, 2025
Why does my Graco Paint Sprayer run erratically?
- F
  ffoxAug 26, 2025
  If your Graco Paint Sprayer system speeds up or runs erratically, it could be due to empty fluid containers, so check them often and keep them filled. Another cause might be air in the fluid lines; purge the lines and check the connections. Also, worn or damaged displacement pump parts can cause this issue; in that case, repair the pump.
D
Danielle HallAug 27, 2025
What to do if resin output pressure drops on both strokes of Graco Paint Sprayer?
- A
  Andrea BryantAug 27, 2025
  If your Graco Paint Sprayer pump operates, but the resin output pressure drops on both strokes, it could be due to a hardener output restriction. Clean and unplug the hardener side, and open the manifold restrictor. Alternatively, the fluid supply might be low, so refill or change the container.
S
Shannon LynchAug 27, 2025
What to do if hardener output pressure drops on both strokes of Graco Paint Sprayer?
- J
  Jack MillerAug 28, 2025
  If your Graco Paint Sprayer pump operates, but the hardener output pressure drops on both strokes, it could be due to a resin output restriction. Clean and unplug the resin side. Alternatively, the fluid supply might be low, so refill or change the container.
C
Christopher RyanAug 29, 2025
Why do the pressure gauges split at the top changeover on my Graco Paint Sprayer?
- K
  Kelly AlexanderAug 29, 2025
  If the fluid outlet pressure gauges on your Graco Paint Sprayer split only at the top changeover, it may be caused by not fully loading one side on the upstroke. To fix this, increase the feed pressure on the side that dropped, increase the feed hose size, and clean the inlet strainer or hopper screen. Another potential cause is air mixed in the fluid from excessive agitation or circulation, in which case you should flush and add new fluid.
G
George RichardsonAug 30, 2025
What to do if resin output pressure drops on upstroke of Graco Paint Sprayer?
- A
  Albert PhillipsAug 30, 2025
  If your Graco Paint Sprayer pump operates, but the resin output pressure drops on the upstroke, it could be due to a dirty, worn, or damaged resin pump piston valve or piston packings. In this case, you should clean and repair the pump.
B
Bruce MillerSep 1, 2025
What to do if resin output pressure drops on downstroke of Graco Paint Sprayer?
- M
  Mary MurphySep 1, 2025
  If your Graco Paint Sprayer pump operates, but the resin output pressure drops on the downstroke, it could be due to a dirty, worn, or damaged resin pump intake valve. In this case, you should clean and repair the pump.
K
Keith HeathSep 2, 2025
What to do if hardener output pressure drops on upstroke of Graco Paint Sprayer?
- M
  Melinda GomezSep 2, 2025
  If your Graco Paint Sprayer pump operates, but the hardener output pressure drops on the upstroke, it could be due to a dirty, worn, or damaged hardener pump piston valve or piston packings. In this case, you should clean and repair the pump.
G
Guy BatesSep 4, 2025
What to do if hardener output pressure drops on downstroke of Graco Paint Sprayer?
- R
  Rachel RiggsSep 4, 2025
  If your Graco Paint Sprayer pump operates, but the hardener output pressure drops on the downstroke, it could be due to a dirty, worn, or damaged hardener pump intake valve. In this case, you should clean and repair the pump.