EasyManua.ls Logo

Grizzly G9742 - User Manual

Grizzly G9742
44 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
MODEL G9742
5"x 6" METAL-CUTTING
BANDSAW w/ SWIVEL HEAD
OWNER'S MANUAL
(For models manufactured since 11/06)
COPYRIGHT © NOVEMBER, 2005 BY GRIZZLY INDUSTRIAL, INC. REVISED FEBRUARY, 2013 (TS)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#PC7670 PRINTED IN CHINA

Table of Contents

Questions and Answers

  • E
    Erica BurkeNov 22, 2025
    Why does my Grizzly Saw not start or trip the breaker?
    • M
      Melissa WallaceNov 22, 2025
      If your Grizzly Saw doesn't start or the breaker trips, there could be several reasons. It might be due to a faulty or incorrectly wired plug/receptacle, in which case you should test the contacts and correct the wiring. The start capacitor could be defective and require testing or replacement. Check if the wall fuse/circuit breaker is blown/tripped and ensure it's the correct size for the machine load, replacing it if weak. Incorrect motor wiring connections can also cause this issue, so verify and correct them. Ensure the power supply is properly functioning and switched ON, with the correct voltage on all legs. A faulty ON/OFF switch may also be the culprit, requiring replacement. Inspect the wiring for any open circuits or high resistance due to broken wires or corroded connections, re...
  • B
    Brandi EspinozaNov 24, 2025
    What to do if my Grizzly G9742 stalls or is underpowered?
    • M
      Mark ClarkNov 24, 2025
      If your Grizzly Saw stalls or seems underpowered, several factors could be the cause. You might be using the wrong blade for the workpiece material, so ensure you have the correct blade for the type of cutting you're doing. The workpiece material itself could be unsuitable, so verify it's appropriate for your cutting task. A feed rate or cutting speed that's too fast can also lead to stalling, so try decreasing it. Check if the blade is slipping on the wheels and adjust the tracking and tension accordingly. Low power supply voltage can also cause this, so ensure the hot lines have the correct voltage. Motor bearing issues can also lead to stalling, indicated by rotational grinding or a loose shaft, requiring bearing replacement. A faulty plug/receptacle may be the cause, so test for good c...

Summary

Introduction

Foreword

Welcome message and overview of the manual's purpose and the bandsaw.

Contact Information

Grizzly Industrial contact details for comments, support, and service inquiries.

Machine Data Sheet

Product and Shipping Specifications

Details on machine weight, dimensions, and shipping requirements.

Electrical and Motor Details

Information on power requirements, voltage, current, and motor specifications.

Cutting Capacities and Construction

Maximum material sizes and construction materials of key machine parts.

Table and Other Specifications

Specifications for table size, wheel size, and other general machine data.

Identification of Machine Components

Section 1: Safety

General Safety Instructions

Essential safety warnings and guidelines for operating machinery.

Additional Safety for Metal Cutting Bandsaws

Specific safety precautions tailored for metal cutting bandsaw use.

Section 2: Circuit Requirements

Electrical Connection and Safety

Guidelines for power connection, voltage selection, and electrical safety.

Section 3: Set Up

Initial Setup and Safety Procedures

Covers setup safety, required items, unpacking, and initial inventory.

Inventory and Parts Check

Lists components and hardware included with the machine for inventory.

Cleaning and Site Preparation

Instructions for cleaning the machine and choosing a suitable operating location.

Cabinet, Wheels, and Feet Assembly

Steps for assembling the cabinet base, wheels, and rubber feet.

Shipping Strap and Vise Alignment

Procedures for removing shipping restraints and squaring the vise.

Chip Tray and Auto Shut-Off Setup

Installing the chip tray and setting the automatic shut-off lever.

Pulley Cover Installation

Steps for correctly installing the pulley cover for safe operation.

Test Run Procedure

Recommended Adjustments Verification

Section 4: Operations

Operational Safety Guidelines

Safety rules and precautions to follow during machine operation.

Blade Speed Selection and Adjustment

How to choose and change blade speeds for different materials.

Blade Selection Guide

Chart and rules for choosing the correct bandsaw blade for materials.

Feed Rate Control

How to adjust the feed rate for optimal cutting performance.

Blade Guide Adjustment

Steps for properly aligning and adjusting the blade guides.

Blade Tensioning

Importance and procedure for setting correct blade tension.

Operation Tips and Best Practices

Advice for safe and efficient bandsaw operation and blade longevity.

Section 5: Accessories

Section 6: Maintenance

Maintenance Schedule

Recommended checks and tasks for daily, monthly, and annual maintenance.

Cleaning Procedures

How to clean the bandsaw to maintain performance and longevity.

Lubrication Points and Schedule

Locations and frequency for lubricating machine parts for optimal function.

Section 7: Service

Troubleshooting Common Issues

Solutions for problems related to motor, electrical, and operational issues.

Blade Change Procedure

Step-by-step guide for safely replacing the bandsaw blade.

Blade Tracking Adjustment

How to adjust the blade tracking for proper wheel alignment.

Electrical Components Overview

Identification and images of key electrical parts like the capacitor.

Wiring Diagram and Connections

Schematic showing 110V and 220V wiring configurations.

Saw Parts Breakdown

Stand Parts Breakdown

Guides & Shafts Parts Breakdown

Labels Parts Breakdown

Warranty Card

Warranty and Returns Policy

Grizzly G9742 Specifications

General IconGeneral
BrandGrizzly
ModelG9742
CategorySaw
LanguageEnglish

Related product manuals