Why is my Haier HW120-B14876N vibrating so much during spinning?
Strong vibrations during spinning can occur if the transportation bolts haven't been removed, the appliance isn't on solid, level ground, or the machine load is incorrect. Remove all transportation bolts. Ensure the washer is on solid ground and leveled. Check the load weight and balance.
What to do if my Haier HW120-B14876N is not draining properly?
A drainage failure can occur if the drain hose is blocked or if the drain hose end is higher than 100 cm above the floor level. Unblock the drain hose. Ensure that the drain hose is properly installed.
Why is my Haier HW120-B14876N Washer not working?
Your Haier Washer might not be operating because the program hasn't started, the door isn't closed properly, the machine hasn't been switched on, there's a power failure, or the child lock is activated. Check the program and start it. Close the door properly. Switch the machine on. Check the power supply. Deactivate the child lock.
Why is my Haier HW120-B14876N not filling with water?
If your Haier Washer isn't filling with water, it could be due to no water supply, a kinked inlet hose, low water pressure (less than 0.03 MPa), an improperly closed door, or a water supply failure. Check the water tap. Check the inlet hose. Check the water pressure. Close the door properly. Ensure the water supply.
What to do if my Haier Washer stops mid-cycle?
If your Haier Washer stops before completing the wash cycle, it might be due to a water or electric failure. Check the power and water supply.
How to fix CLR FLTR error on Haier HW120-B14876N?
The CLR FLTR error on your Haier Washer indicates a drainage error. Check the drain hose installation.
Why is my Haier HW120-B14876N Washer draining immediately?
If your Haier Washer is draining immediately, it could be because the height of the drain hose is below 80 cm or the drain hose end is submerged in water. Ensure that the drain hose is properly installed and is not in water.
Why is the Haier HW120-B14876N Washer spinning failing?
If the spinning is failing, check the machine load and laundry, and then run the spinning program again.
Why does my Haier Washer have excessive foam in the detergent drawer?
Excessive foam in the detergent drawer of your Haier Washer can be caused by using an inappropriate detergent or using too much detergent. Check detergent recommendations and reduce the amount of detergent used.
What to do if my Haier HW120-B14876N shows error E2?
The E2 error on your Haier Washer indicates a lock error. Shut the door properly.
Precautions before first use and during daily operation.
Safety measures for maintenance, cleaning, and installation.
Specifies authorized usage and general safety warnings.
Visual identification of appliance parts and rear components.
Lists and shows the items supplied with the washing machine.
Explains the appliance's display, detergent drawer, and basic buttons.
How to select programs and start/pause cycles.
Details of specific function buttons like Extra Rinse, Delay, i-time, Steam, Speed, Temp, Child Lock.
Details available wash programs, load capacity, temperature, and spin speed.
Explains how the appliance adjusts settings based on load size.
Connecting power/water, preparing laundry, selecting detergent.
Steps for running cycles, starting, stopping, and after-wash actions.
Advice on saving energy, water, and detergent.
Steps for cleaning the detergent drawer and the appliance exterior.
How to clean the water inlet filter and the washing drum.
Procedures for cleaning the pump filter and preparing for long periods of disuse.
Explains various status codes displayed by the appliance.
Solves common problems indicated by specific error codes on the display.
Addresses issues without codes, foam formation, and actions during power failure.
Steps for unpacking the appliance and disposing of packaging materials.
Removing transport bolts and leveling the appliance for stability.
Steps for connecting the water inlet hose and the electrical plug.
Lists voltage, current, power, water pressure, and weight.
Provides detailed dimensions for different models and space requirements.
Information on EC directives and CE marking compliance.
Information on contacting Haier support and required data.
Provides postal addresses for Haier service centers in Europe.
General| Door hinge | Left |
|---|---|
| Water fill | Cold |
| Control type | Buttons, Rotary |
| Display type | LED |
| Loading type | Front-load |
| Drum material | Stainless steel |
| Product color | White |
| Country of origin | China |
| Custom panel-ready | - |
| Appliance placement | Freestanding |
| Inverter technology | Yes |
| Drum capacity | 12 kg |
| Wi-Fi controlled | No |
| Delay start (max) | 24 h |
| Residual moisture | 52 % |
| Spin-drying class | B |
| Maximum spin speed | 1400 RPM |
| Noise level (spin) | 65 dB |
| Noise level (wash) | 53 dB |
| Number of washing programs | 14 |
| Power plug type | Type G |
| Water consumption per cycle | 56 L |
| Package depth | 752 mm |
| Package width | 684 mm |
| Package height | 962 mm |
| Package weight | 89000 g |
| Customs product code (TARIC) | 8450200000 |
| Quantity per shipping (inner) case | 1 pc(s) |
| Quantity per intermodal container (40ft, HC) | 90 pc(s) |
Weight and Dimensions| Depth | 600 mm |
|---|---|
| Width | 595 mm |
| Height | 850 mm |
| Weight | 80000 g |
To Next Page