Harman Kardon DPR 1001 - Front Panel Controls Overview; Front Panel Button Functions (Part 1); Front Panel Connection Jacks

A) ANALOG INPUT, BASELINE AUDIO PARAMETERS(STEREOSURROUNDMODE)
Measuring methods are based on IHF and IEC standard 268-3
Measurement conditions,unless otherwise noted :
Tone Off or Tone(Bass,Treble), Balance, EQ control : Center Position , Other SW's : OFF, Volume:Max
Nominal input level : 0dBFS sine wave PCM bitstream(Digital), 225mV sine wave (Analog)
Power figures should be kept minimum 10min., between 15 and 35
o
C
.
Terminator : 1kohm for general purpose inputs
All Voltage Measurements are made with RMS detector, unless otherwise specified.
Filter : IHF-A filter
UUT= Unit Under Test.
Power supply : 120 V , 60 Hz
MARKETING UNIT RATINGS. CONDITION UNIT VALUE
Watts/Ch 50
Watts/Ch 50
Ohm
8 ohm, +/-
1 %,
Non-Inductive,
455 W
SPEAKER AVAILABLE SPEAKER MODES
*SUB-WOOFER SPKR:YES *SPKR LEVEL:ALL 0dB *TONE OUT
☞
SPEAKER POWER AMPLIFIER SECTION
1 1kHz
2
VOL at min. 10Hz-22KHz BW, peak detector, all inputs
terminated w/ 1 Kohm
mVpk
<3mV <2mV
VOL at min. 10Hz-22KHz BW, peak detector, all inputs
terminated w/ 1 Kohm
mVpk
<2.5mV
<1.5mV
VOL at max. 10Hz-22KHz BW, peak detector, all inputs
terminated w/ 1 Kohm
mVpk
<10mVpk
<8mVpk
VOL at max. 10Hz-22KHz BW, peak detector, all inputs
terminated w/ 1 Kohm
mVpk
<4mVpk
<2.5mVpk
VOL at max. 10Hz-22KHz BW, RMS , non-weighted, all inputs
terminated w/ 1 Kohm
mVrms
<4mVrms
<3mVrms
VOL at max. 10Hz-22KHz BW, RMS , non-weighted, all inputs
terminated w/ 1 Kohm
mVrms
<1mVrms
<0.75mVrms
VOL at max. 10Hz-22KHz BW, RMS , 'A Weighted', all inputs
terminated w/ 1 Kohm
mVrms
<3mVrms
<2.5mVrms
VOL at max. 10Hz-22KHz BW, RMS , 'A Weighted', all inputs
terminated w/ 1 Kohm
mVrms
<0.7mVrms
<0.5mVrms
VOL at max. 10Hz-22KHz BW, RMS , 'A Weighted', all inputs
left un-terminated
mVrms
<3mVrms
<2.5mVrms
VOL at max. 10Hz-22KHz BW, RMS , 'A Weighted', all inputs
left un-terminated
mVrms
<0.7mVrms
<0.5mVrms
8CH
STEREO
8CH
STEREO
8CH
STEREO
8CH
STEREO
8CH
STEREO
8CH
STEREO
20Hz
1k
20k
225±40
225±20
<0.6
<0.45
Rated Stereo Power Output
Rated 8 CH DIRECT Power Output
Rated Resistive Load
Both FL andFR Speaker amplifiers driven and loadedwith Rated
Resistiv
e
Load.
All Seven (FL,FR,C,SL,SR,SBL,SBR) Speaker amplifiers driven and
loaded with Rated Resistive Load Impedance.
Resistiveloads tobe connectedto Speaker Outputs using a 12 AWG
StrandedSpeaker Wire pair for eachload resistor. Wirelength should
beapproximately10 feet.
LARGE ALWAYS
YES/NO
InputSensitivity
FRONT "L" AND "R" SPEAKERS
SUBWOOFER OUTPUT
RESIDUAL NOISE
TOTAL
HARMONIC
DISTORTION
(Rated Stereo
Powe
r
O
u
t
p
u
t
-
1
dB)
Should be met by
all Stereo Inputs
Stereo and 8 CH DIRECT rated Power into Rated Resistive
Load should be obtained by applying an input signal level
with
the specified range.
mV
Should be met by
all AnalogStereo
and 8CH DIRECT
Inputs
20Hz-20 KHz,
Power out =Rated
Power - 1 dB
Should be met by
all AnalogStereo
and 8 CHDIRECT
Input
s
Vol at Max, 10 Hz-22KHz Meas BW."A"WEIGHTED
%
LIMIT
NOMONAL
No
DESCRIPTION
INPUT
FREQ.
REMARK
UNIT
5
DPR1001 harman/kardon
DETAILED SPECIFICATIONS