Heat Controller HBH Series - Page 15

Engineering Design Guide HBH SERIES Heat Controller, Inc.
15
Blower Performance Data - HBH096 Standard Unit
Table Continued from Previous Page
All Data is Wet Coil
A = Standard Static/Standard Motor, B = Low Static/Standard Motor, C = High Static/Standard Motor, D = Standard Static/Large Motor, E = High Static/Large Motor
Unit factory shipped with standard static sheave and drive at 2.5 turns open. Other speed require fi eld selection.
For applications requiring higher static pressures, contact your local representative. Performance data does not include drive losses and is based on sea level conditions.
Do not operate in black regions. All airfl ow is rated at lowest Voltage if unit is dual Voltage rated, i.e. 208V for 208-230V units.
SCFM ESP 0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50
3300
BHP 1.01 1.08 1.14 1.21 1.28 1.33 1.39 1.45 1.51 1.58 1.64 1.72 1.78 1.84 1.93 2.00
Sheave/Mtr B A A A A A A A A A C C C C C E
RPM 755 790 820 855 890 915 945 975 1005 1035 1060 1090 1115 1140 1170 1195
Turns Open 1 5.5 5 4 3.5 3 2.5 2 1.5 1 4 3.5 3 3 2.5 2
3400
BHP 1.08 1.15 1.22 1.29 1.35 1.41 1.47 1.53 1.59 1.68 1.75 1.83 1.90 1.96 2.02 2.08
Sheave/Mtr A A A A A A A A A A C C C C E E
RPM 765 800 835 870 900 930 960 990 1015 1045 1070 1100 1125 1150 1175 1200
Turns Open 6 5 4.5 4 3.5 3 2.5 2 1.5 1 4 3.5 3 2.5 2 2
3500
BHP 1.16 1.23 1.29 1.36 1.42 1.48 1.54 1.60 1.66 1.73 1.79 1.85 1.92 2.01 2.09 2.17
Sheave/Mtr A A A A A A A A A C C C C E E E
RPM 780 815 845 880 910 940 970 1000 1025 1055 1080 1105 1130 1160 1185 1210
Turns Open 5.5 5 4.5 3.5 3 2.5 2 1.5 1 4.5 4 3.5 3 2.5 2 1.5
3600
BHP 1.24 1.30 1.37 1.44 1.51 1.58 1.65 1.72 1.78 1.86 1.92 1.98 2.06 2.13 2.21 2.29
Sheave/Mtr A A A A A A A A A C C C E E E E
RPM 795 825 860 890 920 950 980 1010 1035 1065 1090 1115 1145 1165 1190 1215
Turns Open 5.5 4.5 4 3.5 3 2.5 2 1.5 1 4 3.5 3 2.5 2.5 2 1.5
3700
BHP 1.34 1.40 1.46 1.53 1.61 1.68 1.75 1.82 1.90 1.97 2.06 2.13 2.21 2.28 2.36 2.44
Sheave/Mtr A A A A A A A A C C E E E E E E
RPM 820 850 880 910 940 970 1000 1025 1055 1080 1110 1135 1160 1180 1205 1230
Turns Open 5 4.5 3.5 3 2.5 2 1.5 1 4.5 4 3.5 3 2.5 2 1.5 1.5
3800
BHP 1.43 1.49 1.56 1.63 1.70 1.78 1.86 1.94 2.02 2.12 2.20 2.28 2.34 2.42 2.50 2.58
Sheave/Mtr A A A A A A A A E E E E E E E E
RPM 840 870 900 930 960 990 1020 1045 1070 1100 1125 1150 1170 1195 1220 1245
Turns Open 4.5 4 3.5 3 2.5 2 1.5 1 4 3.5 3 2.5 2.5 2 1.5 1