How long does setup charging take on Heraeus Digilance V Measuring Instruments?
If your Heraeus Measuring Instruments are setting up charging, it means charging is configuring. Wait a few seconds for the setup to configure.
What does charging error mean for Heraeus Measuring Instruments?
If your Heraeus Measuring Instruments display a charging error, it indicates an error occurred during charging, and no charging is possible. Check the state of health of the battery. Consult Heraeus Electro-Nite.
General| Brand | Heraeus |
|---|---|
| Model | Digilance V |
| Category | Measuring Instruments |
| Language | English |
Provides general information about the manual and its intended audience.
Defines personnel authorized to operate and service the instrument.
Explains safety notice terms (Danger, Warning, Caution) and pictograms.
Details correct applications and adherence to safety guidelines.
Outlines compliance with EU RoHS directives for hazardous substances.
Explains EU WEEE directive for disposal and commercial use.
Provides precautions for handling and disposal of the Lithium Ion battery.
Guides on recycling components like electronic cards and battery packs.
Declares compliance with essential EU directives like EMC and LVD.
Details FCC/IC compliance for wireless models, interference, and RF exposure.
Describes the Digilance V as a hand-held instrument for molten metal temperature measurement.
Explains how to set the instrument to transport mode to conserve battery life.
Details requirements for packing and shipping ESD-sensitive electronic modules.
Provides guidelines for packing the instrument for dispatch and overseas transport.
Covers regulations for shipping the instrument with its Lithium Ion battery pack.
Guides on the initial activation and basic setup of the Digilance V.
Step-by-step instructions for installing the immersion lance and connecting cables.
Provides a reference for thermocouple wire color codes for EU and US standards.
Explains the process of taking temperature measurements with the instrument.
Details how measurement results are evaluated based on time windows and conditions.
Describes how to access and view stored measurement results.
Explains how to label measurements with Heat Number and Place.
Provides instructions on setting and editing the Heat Number for measurements.
Guides on configuring and selecting measurement place names.
Details the procedure for charging the instrument's Lithium Ion battery pack.
Explains settings for controlling instrument awake time and transport mode.
Information on accessing configuration settings and the default password.
Lists and explains various configurable parameters for instrument setup.
Details settings for wireless ID, mode, and data telegrams.
Configures the unique identification number for wireless communication.
Sets the operating mode for wireless data transmission (e.g., MC Telegram).
Defines the format and content of data telegrams for wireless transmission.
Assigns an identifier for melt control functions via wireless.
Outlines rules for qualified personnel and authorized repairs.
Provides precautions for handling electronic modules susceptible to electrostatic discharge.
Instructions on how to clean the instrument using a damp cloth.
States that the battery should not be replaced by the user.
Describes how to perform a test measurement using a Checkmate instrument.
Details that calibration must be performed by authorized personnel annually.
Sensor, contact piece, or cable defect. Exchange components or correct connection.
Reversed polarity of measuring cable. Connect cable correctly.
Charging is configuring. Wait for setup to complete.
Battery is charging. No specific action required.
Battery is fully charged. No action needed.
Adapter connected but no power. Apply power to the adapter.
Temperature too high. Lower instrument temperature.
Battery too cold for charging. Wait for temperature to rise.
Battery too hot for charging. Lower instrument temperature.
Error during charging. Check battery health.
Accelerometer is switched off. Accelerometer will be reactivated upon power-on.
Thermocouple is broken. Apply new thermocouple or check wiring.
No evaluation possible. Review window settings.
Not possible to compensate. Reference temperature measurement defective. Consult manufacturer.
Measured temperature out of range. Check TC type and start temperature.
Specifies single/multi-dip measurement and analog input channel.
Details the sampling frequency and temperature measurement ranges for different thermocouples.
Refers to standard tables and specifies thermocouple accuracy.
Covers configurable display units and storage of measurement results.
Information on power source, charging voltage, and nominal battery operating hours.
Details wireless range, frequency, power, and operating temperature limits.
Specifies IP rating, physical dimensions, and weight of the instrument.
Part number for replacing the instrument's battery pack.
Part number for the rubber protective boot for the instrument.
Part number for replacing the standard instrument housing.
Part number for replacing the wireless version instrument housing.
Part number for the antenna assembly used for wireless communication.
Part number for the thermocouple connection screw.
Part number for the screws used to secure the front plate.
Part number for the bolt used to secure the lance.
Part number for the 12V DC power supply unit.
Information on obtaining lances and cable assemblies.
To Next Page