Operation
Remote control models
1. Check that the tilt lock lever is in the lock
positíon.
2.
Pull up the neutral inte
rl
ock trigger (if
equipped) and move the remote control
lever quickly and firmly
fr
om neutral to
reverse.
Stopping engine
Before stopping
th
e engine, first let it cool oft
for a few minutes at idle or low speed. Stop-
3.
Disconnect the
fu
el line if you are using
pi
ng the engine immediately after operating an external
fu
el tank.
at high speed is not recommended.
Procedure
1. Push and hold the engine st
op
button
until the engine comes to a complete
stop
2.
After stopping the engine, tighten the aír
vent screw on the fuel tank cap and set
the fuel cock lever or
kn
ob to the closed
position
, if e
qu
ipped.
21
NOTE
:
If the outboard motor is equipped with an
en-
gine stop switch lanya
rd
, the engine can also
be
stopped by pulling the lanyard and remov-
ing the lock plate from the eng
in
e stop
switch
Trimming
outboard
motor
The trim angle of the outboard motor helps
determine the position of the bow of the boat
in the wate
r.
Correct t
ri
m angle will help im-
prove
pe
斤
。rm
a
n
ce
and fuel economy while
r
ed
ucing strain on the eng
in
e. Correct trim
an
gle depends upon the combina
ti
on of
boat
, engine, and propelle
r.
Correct t
rim
is
also affected by variables such as the load in
the boat
, sea conditions, and running speed
,,
..
协
1:1~
1I~【帽
Excessive
trim
for
the
operating
condi-
tions
(either
trim
up
or
trim
down)
can
cause
boat
instability
and
can make
steering the
boat
more
difficul
t.
This
in-
creases
the
possibility
of
an accideh
t.
If
the
boat
begins
to
feel unstable
or
is
hard
to
steer,
slow
down
and/or
readjust
the
trim
angle.
」
γ
二
1. T
ri
m
ope
ra
tin
g
angle
Adjusting
trim
angle
for
manual
tilt
models
There a
re
4 or 5 holes pro
vi
ded
in
the ciamp
bracket to adjust the outboard motor trim an-
gl
e.
1.
Stop
th
e engine.
2.
Remove the trim
rod
from the clamp
Operation
br
acket while slightly tilting the outboa
rd
motor up.
1. Trim
rod
3.
Reposition the rod
in
the desired hol
e.
To ra
is
e
th
e b
ow
("trim-ou
t"
),
move the
ro
d
away from the transom
To lower the bow ("trim-in")
, move the rod to-
wa
rd the tran
so
m.
Make test
run
s with the trim set to different
angles to find
tn
e p
os
ition that wo
rk
s best for
yo
ur boat and operating conditions
，?‘
.'I'H:I~II~
【帽
•
Stop
the
engine
before
adjusting
the
trim
angle.
• Use care
to
avoid
being pinched when
removing
or
installing
the rod.
• Use
caution
when
trying
a
tr
im
position
for
the
first
time. Increase speed gradu-
ally
and
watch
for
any
signs
of
instabil-
ity
or
control
problems.
Improper
trim
angle can cause
loss
of
cont
rol.
NOTE
:
The outboard motor trim angle can be
changed approximately 4 degrees by shifting
the trim
rod
one hole.
Adjusting
boat
trim
Wh
en the boat is on plane, a bo
w-
up attitude
22
To Next Page
Loading...
Need help?
General
