To Next Page
V
vjonesAug 16, 2025
How to release Hilti Drill bit?
- LLinda Valentine MDAug 16, 2025
If you can’t release the drill bit from your Hilti Drill, make sure that the chuck is pulled back as far as it will go. Then, remove the accessory tool.
How to release Hilti Drill bit?
If you can’t release the drill bit from your Hilti Drill, make sure that the chuck is pulled back as far as it will go. Then, remove the accessory tool.
What to do if Hilti TE 30 Power Tool drill bit does not rotate?
If the drill bit of your Hilti Power Tool does not rotate, the function selector switch might not be engaged or is in the “Chiseling” or “Chisel adjustment” position. Set the function selector switch to “Drilling without hammering” or “Hammer drilling.”
What to do if Hilti Power Tool drill bit cannot be released?
If the drill bit of your Hilti Power Tool cannot be released, the chuck might not be pulled back fully. Pull the chuck back as far as it will go and remove the accessory tool.
Why does my Hilti Drill keep turning off?
If your Hilti Drill doesn't start or switches off during use, the issue might be with the power supply. Try plugging in another electrical device to check if the outlet is working. Alternatively, the carbon brushes may be worn. In this case, have a trained electrician inspect the drill and replace the brushes if needed.
Why doesn't my Hilti Combihammer have full power?
If your Hilti combihammer isn’t achieving full power, it could be due to several reasons. First, ensure that you are using an extension cord with an adequate conductor cross section. Second, make sure the control switch is fully pressed. Third, check that the tool is set to forward rotation. Finally, verify that the voltage from the generator is correct.
Why Hilti TE 30 doesn’t start?
If your Hilti Power Tool doesn’t start, it could be due to an interruption in the electric supply. To check this, plug in another electric tool or appliance to see if it works. Another possible cause is worn-out carbon brushes. If this is the case, have the power tool checked by a trained electrical specialist, and have the carbon brushes replaced if necessary.
Why Hilti combihammer doesn’t achieve full power?
If your Hilti combihammer isn’t achieving full power, the gauge (cross section) of the extension cord conductors may be inadequate. Use an extension cord with an adequate conductor cross section. Also, make sure the control switch is fully pressed. Press the control switch as far as it will go.
What to do if Hilti TE 30 Power Tool drill bit makes no progress?
If the drill bit of your Hilti Power Tool makes no progress, the tool may have been set to reverse rotation. Set the tool to forward rotation.
What to do if my Hilti Drill has no hammering action?
If your Hilti Drill has no hammering action, it may be due to several factors. First, if the power tool is too cold, bring the tip of the drill bit into contact with the working surface, switch the rotary hammer on and allow it to run. Repeat if necessary. Second, check that the function selector switch is set to the “Hammer drilling” position, not “Rotary drilling only”. Third, increase contact pressure to activate the hammer mechanism.
Why Hilti TE 30 has no hammering action?
If your Hilti Power Tool has no hammering action, it could be because the tool is too cold. Bring the tip of the drill bit into contact with the working surface, switch the rotary hammer on, and allow it to run. If necessary, repeat the procedure until the hammering mechanism begins to operate. Another possible cause is that the function selector switch is set to “Rotary drilling only”. Set the function selector switch to the “Hammer drilling” position.
General| Drilling | Yes |
|---|---|
| Chuck type | SDS Plus |
| Product color | Black, Red |
| Country of origin | Germany |
| Rated speed (max) | 1100 RPM |
| Impact energy (max) | 3.6 J |
| Vibration level (hammer drilling) | 16.8 m/s² |
| Drilling diameter in concrete (max) | 28 mm |
| Optimum drilling diameter (concrete) | 10 - 20 mm |
| Noise level | 92 dB |
| Input power | 1010 W |
| Power source | AC |
| Power plug type | Type C |
| Quantity per shipping (inner) case | 1 pc(s) |
Weight and Dimensions| Weight | 4100 g |
|---|---|
| Package depth | 3456 mm |
| Package width | 2000 mm |
| Package height | 4500 mm |
| Package weight | 4500 g |
