What to do if my Hilti Drill doesn't start?
If your Hilti Drill doesn't start, first check for any power interruption by plugging in another electrical tool to see if it works. If there was a power interruption, the electronic restart interlock may be activated. Try switching the power tool off and then on again.
What to do if drill bit can’t be released from Hilti TE 50?
If you can't release the drill bit from your Hilti Power Tool, it might be due to: * The chuck not being pulled back fully. Pull the chuck back as far as it will go and then try removing the accessory tool. * The side handle not being fitted correctly. Release the side handle and refit it correctly so that the clamping band and side handle engage in the recess.
How to restart Hilti TE 50?
If your Hilti Power Tool doesn't start, it might be due to the electronic restart interlock being activated after a power interruption. Try switching the power tool off and then on again to resolve this.
How to release chisel from Hilti Drill chuck?
If the chisel cannot be released from the chuck of your Hilti Drill, it may be because the chuck is not pulled back fully. Pull the chuck back as far as it will go and then remove the accessory tool.
Why doesn't the drill bit rotate on my Hilti Drill?
If the drill bit on your Hilti Drill doesn’t rotate, the function selector switch might not be engaged or is in the incorrect position. Set the function selector switch to “Drilling without hammering” or “Hammer drilling”.
How to fix no hammering action on Hilti Drill?
If your Hilti Drill has no hammering action, it might be too cold. Bring the tip of the drill bit into contact with the working surface, switch the rotary hammer on and allow it to run. Repeat this procedure if necessary, until the hammering mechanism begins to operate.
What to do if Hilti Drill doesn't start and service indicator is red?
If your Hilti Drill does not start and the service indicator shows red, the carbon brushes may be worn out. Have the power tool checked by a trained electrical specialist, and have the carbon brushes replaced if needed. Alternatively, there could be an electrical fault. Have the tool checked by Hilti Service.
How to fix Hilti Drill that doesn't start?
If your Hilti Drill doesn't start, there could be several reasons: * There might be an interruption in the electric supply. To check this, plug in another power tool or appliance to see if it works. * The supply cord or plug could be defective. In this case, have a trained electrical specialist check and replace it if necessary. * The generator might be in sleep mode. Apply a load to the generator by connecting a second power consumer, such as a work light. * There could be an electrical fault. Have the power tool and supply cables checked by a trained electrical specialist. * The electronic restart interlock may be activated after an interruption in the electric supply. Try switching the power tool off and then on again.
What to do if the drill bit doesn't rotate on my Hilti Drill?
If the drill bit on your Hilti Drill isn’t rotating, check that the function selector switch is set to the 'Hammer drilling' position. Also, ensure that the chuck is pulled back as far as it will go to properly release and remove the accessory tool.
General| Carrying case | Yes |
|---|---|
| Input power | 1050 W |
| Power source | AC |
| Impact rate | 3180 bpm |
| Rated speed (max) | 550 RPM |
| Impact energy (max) | 5.2 J |
| Vibration level (hammer drilling) | 16.1 m/s² |
| Drilling diameter in concrete (max) | - mm |
| Chuck type | SDS Max |
| Product color | Black, Red |
Weight and Dimensions| Depth | 462 mm |
|---|---|
| Width | 113 mm |
| Height | 243 mm |
| Weight | 5700 g |
Guidance on reading and using the operating instructions for safe operation.
Explanation of signal words and symbols used in the document and illustrations.
Details the symbols found on the product itself and their meanings.
Provides product details like type designation, serial number, and intended use.
Crucial general safety advice for operating power tools, including work area and electrical safety.
Emphasizes staying alert, using PPE, preventing unintentional starting, proper stance, and attire.
Covers using the correct tool, checking the switch, disconnecting power, and storing tools safely.
Specific safety precautions for hammer drilling operations, including ear protection and handle usage.
Focuses on using the product in faultless condition, proper gripping, and avoiding rotating parts.
Advises checking the work area for cables/pipes before starting work.
Covers switching off for jams and waiting for complete stop before laying down.
Visual identification and numbering of the product's main components.
Details detachable cord version, intended use, and potential misuse scenarios.
Defines the product's primary applications and operational requirements.
Outlines situations and environments where the product should not be used.
Explains the AVR system that reduces operational vibration.
Describes the keyless chuck for rapid accessory tool changes.
Details the function and meaning of the product's LED service indicator.
Lists the components included with the product purchase.
Specifies ambient temperature and drill bit size ranges for operation.
Essential steps before commencing work, including safety precautions.
Step-by-step guide on how to attach and position the side handle.
Instructions for attaching and setting the depth gauge for controlled drilling depth.
Procedure for installing and removing accessory tools, including safety notes.
Details different working modes like drilling and chisel positioning.
Procedure for performing hammer drilling operations with the tool.
Guidance on adjusting the chisel angle for optimal performance.
Instructions for performing chiseling operations with the tool.
Method for locking the switch for continuous operation during chiseling.
Steps for securely connecting the detachable power cord to the tool.
Procedure for safely detaching the power cord from the tool and outlet.
General cleaning instructions for the tool's parts and air vents.
Guidelines for maintaining the tool's condition and safety, including repairs.
Recommendations for safely transporting and storing the tool.
Table of common problems, their possible causes, and suggested solutions.
To Next Page
