Hitachi SH1 Series - Page 88

4-45
Chapter 4
For parameter configuration
[Hb150] to [Hb171]
Free V/f setting
Code/Name
Range (unit)
Initial
value
Hb150 Free-V/f frequency 1 setting,
1st-motor
0.00 to
[Hb152](Hz)
0.00
Hb151 Free-V/f voltage 1 setting,
1st-motor
0.0 to 1000.0(V)
0.0
Hb152 Free-V/f frequency 2 setting,
1st-motor
[Hb150] to
[Hb154](Hz)
0.00
Hb153 Free-V/f voltage 2 setting,
1st-motor
0.0 to 1000.0(V)
0.0
Hb154 Free-V/f frequency 3 setting,
1st-motor
[Hb152] to
[Hb156](Hz)
0.00
Hb155 Free-V/f voltage 3 setting,
1st-motor
0.0 to 1000.0(V)
0.0
Hb156 Free-V/f frequency 4 setting,
1st-motor
[Hb154] to
[Hb158](Hz)
0.00
Hb157 Free-V/f voltage 4 setting,
1st-motor
0.0 to 1000.0(V)
0.0
Hb158 Free-V/f frequency 5 setting,
1st-motor
[Hb156] to
[Hb160](Hz)
0.00
Hb159 Free-V/f voltage 5 setting,
1st-motor
0.0 to 1000.0(V)
0.0
Hb160 Free-V/f frequency 6 setting,
1st-motor
[Hb158] to
[Hb162](Hz)
0.00
Hb161 Free-V/f voltage 6 setting,
1st-motor
0.0 to 1000.0(V)
0.0
Hb162 Free-V/f frequency 7 setting,
1st-motor
[Hb160] to
[Hb104](Hz)
0.00
Hb163 Free-V/f voltage 7 setting,
1st-motor
0.0 to 1000.0(V)
0.0
・For the Frequency 1(f1) to the frequency (f7), set values
smaller than the base frequency.
And, for the corresponding voltage 1(V1) to voltage
7(V7), set values smaller than the rated voltage.
In the case of the high-frequency motor, set the base /
maximum frequency at first.
V/f feedback control adjustment
Code/Name
Range (unit)
Initial value
Hb170 Slip compensation
P-gain at V/f with encoder,
1st-motor
0 to 1000(%)
100
Hb171 Slip compensation
I-gain at V/f with encoder,
1st-motor
0 to 1000(%)
100
・When [AA121] is set as feedback control, slip
compensation is possible.
[Hb180] [Hb202] to [Hb280]
Output voltage adjustment
Code/Name
Range (unit)
Initial value
Hb180 Output voltage gain,
1st-motor
0 to 255(%)
100
・When the motor is hunting, there is a possibility that the
motor stabilizes by adjustment of the output voltage gain.
2nd motor When Intelligent Input terminal 024[SET] is enabled.
Code/Name
Range
(unit)
Initial
value
Hb202 Async. Motor capacity setting, 2nd-motor
Same as Hb102
Hb203 Async. Motor number of poles setting,
2nd-motor
Same as Hb103
Hb204 Async. Motor base frequency setting,
2nd-motor
Same as Hb104
Hb205 Async. Motor maximum frequency
setting, 2nd-motor
Same as Hb105
Hb206 Async. Motor rated voltage, 2nd-motor
Same as Hb106
Hb208 Async. Motor rated current, 2nd-motor
Same as Hb108
Hb210 Async. Motor constant R1, 2nd-motor
Same as Hb110
Hb212 Async. Motor constant R2, 2nd-motor
Same as Hb112
Hb214 Async. Motor constant L, 2nd-motor
Same as Hb114
Hb216 Async. Motor constant Io, 2nd-motor
Same as Hb116
Hb218 Async. Motor constant J, 2nd-motor
Same as Hb118
2nd motor When Intelligent Input terminal 024[SET] is enabled.
Code/Name
Range
(unit)
Initial
value
Hb230 Minimum frequency adjustment,
2nd-motor
Same as Hb130
Hb231 Reduced voltage start time setting,
2nd-motor
Same as Hb131
Hb240 Manual torque boost operation mode
selection, 2nd-motor
Same as Hb140
Hb241 Manual torque boost value, 2nd-motor
Same as Hb141
Hb242 Manual torque boost Peak speed,
2nd-motor
Same as Hb142
Hb245 Eco drive enable, 2nd-motor
Same as Hb145
Hb246 Eco drive response adjustment,
2nd-motor
Same as Hb146
Hb250 Free-V/f frequency 1 setting, 2nd-motor
Same as Hb150
Hb251 Free-V/f voltage 1 setting, 2nd-motor
Same as Hb151
Hb252 Free-V/f frequency 2 setting, 2nd-motor
Same as Hb152
Hb253 Free-V/f voltage 2 setting, 2nd-motor
Same as Hb153
Hb254 Free-V/f frequency 3 setting, 2nd-motor
Same as Hb154
Hb255 Free-V/f voltage 3 setting, 2nd-motor
Same as Hb155
Hb256 Free-V/f frequency 4 setting, 2nd-motor
Same as Hb156
Hb257 Free-V/f voltage 4 setting, 2nd-motor
Same as Hb157
Hb258 Free-V/f frequency 5 setting, 2nd-motor
Same as Hb158
Hb259 Free-V/f voltage 5 setting, 2nd-motor
Same as Hb159
Hb260 Free-V/f frequency 6 setting, 2nd-motor
Same as Hb160
Hb261 Free-V/f voltage 6 setting, 2nd-motor
Same as Hb161
Hb262 Free-V/f frequency 7 setting, 2nd-motor
Same as Hb162
Hb263 Free-V/f voltage 7 setting, 2nd-motor
Same as Hb163
Hb270 Slip compensation P-gain at V/f with
encoder, 2nd-motor
Same as Hb170
Hb271 Slip compensation I-gain at V/f with
encoder, 2nd-motor
Same as Hb171
Hb280 Output voltage gain, 2nd-motor
Same as Hb180
Output
frequency(Hz)
f1
f2
f3
f4
f5
f6
f7
0
V2,V3
V1
V5
V6
V7
V4
Output voltage(V)
Base
freq
Maximum
frequency
Voltage
rated value