Hitachi SJ700B SERIES - Page 56

Chapter 4 List of Data Settings
4 - 13
Default
Code Function name Monitored data or setting
_F/_FF _FUF
Setting
during
operation
(allowed or
not)
Change
during
operation
(allowed or
not)
Ter mi na l
C111 Overload setting (2) 0.00 to 1.50 x "rated current" (A) Rated current of inverter
{ {
C121 [O] input zero calibration 0. to 9999., 1000 to 6553 (10000 to 65530) Factory setting
{ {
C122 [OI] input zero calibration 0. to 9999., 1000 to 6553 (10000 to 65530) Factory setting
{ {
Adjustment
C123 [O2] input zero calibration 0. to 9999., 1000 to 6553 (10000 to 65530) Factory setting
{ {
C130 Output 11 on-delay time 0.0 to 100.0 (s) 0.0
¯ {
C131 Output 11 off-delay time 0.0 to 100.0 (s) 0.0
¯ {
C132 Output 12 on-delay time 0.0 to 100.0 (s) 0.0
¯ {
C133 Output 12 off-delay time 0.0 to 100.0 (s) 0.0
¯ {
C134 Output 13 on-delay time 0.0 to 100.0 (s) 0.0
¯ {
C135 Output 13 off-delay time 0.0 to 100.0 (s) 0.0
¯ {
C136 Output 14 on-delay time 0.0 to 100.0 (s) 0.0
¯ {
C137 Output 14 off-delay time 0.0 to 100.0 (s) 0.0
¯ {
C138 Output 15 on-delay time 0.0 to 100.0 (s) 0.0
¯ {
C139 Output 15 off-delay time 0.0 to 100.0 (s) 0.0
¯ {
C140 Output RY on-delay time 0.0 to 100.0 (s) 0.0
¯ {
C141 Output RY off-delay time 0.0 to 100.0 (s) 0.0
¯ {
C142 Logical output signal 1 selection 1
Same as the settings of C021 to C026 (except those of LOG1 to
LOG6)
00
¯ {
C143 Logical output signal 1 selection 2
Same as the settings of C021 to C026 (except those of LOG1 to
LOG6)
00
¯ {
C144
Logical output signal 1 operator
selection
00 (AND), 01 (OR), 02 (XOR) 00
¯ {
C145 Logical output signal 2 selection 1
Same as the settings of C021 to C026 (except those of LOG1 to
LOG6)
00
¯ {
C146 Logical output signal 2 selection 2
Same as the settings of C021 to C026 (except those of LOG1 to
LOG6)
00
¯ {
C147
Logical output signal 2 operator
selection
00 (AND), 01 (OR), 02 (XOR) 00
¯ {
C148 Logical output signal 3 selection 1
Same as the settings of C021 to C026 (except those of LOG1 to
LOG6)
00
¯ {
C149 Logical output signal 3 selection 2
Same as the settings of C021 to C026 (except those of LOG1 to
LOG6)
00
¯ {
C150
Logical output signal 3 operator
selection
00 (AND), 01 (OR), 02 (XOR) 00
¯ {
C151 Logical output signal 4 selection 1
Same as the settings of C021 to C026 (except those of LOG1 to
LOG6)
00
¯ {
C152 Logical output signal 4 selection 2
Same as the settings of C021 to C026 (except those of LOG1 to
LOG6)
00
¯ {
C153
Logical output signal 4 operator
selection
00 (AND), 01 (OR), 02 (XOR) 00
¯ {
C154 Logical output signal 5 selection 1
Same as the settings of C021 to C026 (except those of LOG1 to
LOG6)
00
¯ {
C155 Logical output signal 5 selection 2
Same as the settings of C021 to C026 (except those of LOG1 to
LOG6)
00
¯ {
C156
Logical output signal 5 operator
selection
00 (AND), 01 (OR), 02 (XOR) 00
¯ {
C157 Logical output signal 6 selection 1
Same as the settings of C021 to C026 (except those of LOG1 to
LOG6)
00
¯ {
C158 Logical output signal 6 selection 2
Same as the settings of C021 to C026 (except those of LOG1 to
LOG6)
00
¯ {
Output terminal operation function
C159
Logical output signal 6 operator
selection
00 (AND), 01 (OR), 02 (XOR) 00
¯ {
C160 Input terminal response time setting 1 0. to 200. ( ¯2ms) 1
¯ {
C161 Input terminal response time setting 2 0. to 200. ( ¯2ms) 1
¯ {
C162 Input terminal response time setting 3 0. to 200. ( ¯2ms) 1
¯ {
C163 Input terminal response time setting 4 0. to 200. ( ¯2ms) 1
¯ {
C164 Input terminal response time setting 5 0. to 200. ( ¯2ms) 1
¯ {
C165 Input terminal response time setting 6 0. to 200. ( ¯2ms) 1
¯ {
C166 Input terminal response time setting 7 0. to 200. ( ¯2ms) 1
¯ {
C167 Input terminal response time setting 8 0. to 200. ( ¯2ms) 1
¯ {
Input terminal response
C168
Input terminal response time setting
FW
0. to 200. ( ¯2ms) 1
¯ {
Other
C169
Multistage speed/position
determination time
0. to 200. ( ¯10ms) 0
¯ {