Hitachi YUTAKI S80 Series - Page 171

ENGLISH
Inputs range visualizations and constraints table:
Value
Available at Constraints
1 2 3 4 5 6 7 Visibility
0 Disabled O O O O O O O Always
1 Demand On/Off O O O O O O O
Available if some of the Water Calculation modes (Water calculation mode
for circuit 1 heating (C1WC) or Water calculation mode for circuit 1 cooling
(CC1WC) or Water calculation mode for circuit 2 heating (C2WC) or Water
calculation mode for circuit 2 cooling (CC2WC)) are not set as “Disabled”. It is
not shown if Demand On/Off C1 or Demand On/Off C2 are congured.
2 Smart Act / SG 1 X X X X O X X
Available if 8-200 (“Status” of Smart function in Optional functions menu) is
“Enabled”
3
Swimming Pool
input
X X O X X X X Available if Status (SWP) (“Status” of Swimming pool menu) is “Enabled”
4 Solar X X X O X X X
Available if Solar combination (SOLStSet) (“Status” of Solar combination in
Complementary Heating menu) is “Enabled”
5 Operation Mode O O O O O O O
Available if cooling operation is enabled (DSW1-4: ON). Not available for
YUTAKI S80
6 DHW Boost X X X X X O X
Available if DHW Boost (AutoT) (“DHW Boost” in DHW of the Optional
functions menu) is set as “Open” or “Closed” and Status (DHWs) is set as
“Enabled”
7 Power Meter 1 X X X X X X O
Available if 8-102 (“Power meter 1” in Energy conguration of the Optional
functions menu) is not “Disabled” and Status (PMConf) (“Status” in Energy
conguration of the Optional functions menu) is “Enabled”
8 Demand On/Off C1 O O O O O O O
Available if Water Calculation modes for circuit 1 (Water calculation mode
for circuit 1 heating (C1WC) for heating or Water calculation mode for circuit
1 cooling (CC1WC) for cooling) are not set as “Disabled”. It is not shown if
Demand On/Off is congured.
9 Demand On/Off C2 O O O O O O O
Available if Water Calculation modes for circuit 2 (Water calculation mode
for circuit 2 heating (C2WC) for heating or Water calculation mode for circuit
2 cooling (CC2WC) for cooling) are not set as “Disabled”. It is not shown if
Demand On/Off is congured.
10 Forced Heating O O O O O O O
Available if cooling operation is enabled (DSW1-4: ON). Not available for
YUTAKI S80
11 Forced Cooling O O O O O O O
Available if cooling operation is enabled (DSW1-4: ON). Not available for
YUTAKI S80
12 Power Meter 2 O O O O O O O
Available if 8-103 (“Power meter 3” in Energy conguration of the Optional
functions menu) is not “Disabled” and Status (PMConf) (“Status” in Energy
conguration of the Optional functions menu) is “Enabled”
13
ECO Mode C1&C2
(*1)
O O O O O O O
Available if some of the Water Calculation modes (Water calculation mode
for circuit 1 heating (C1WC) or Water calculation mode for circuit 1 cooling
(CC1WC) or Water calculation mode for circuit 2 heating (C2WC) or Water
calculation mode for circuit 2 cooling (CC2WC)) are not set as “Disabled”. It is
not shown if ECO Mode C1 or ECO Mode C2 are congured.
14 ECO Mode C1 (*1) O O O O O O O
Available if Water Calculation modes for circuit 1 (Water calculation mode for
circuit 1 heating (C1WC) for heating or Water calculation mode for circuit 1
cooling (CC1WC) for cooling) are not set as “Disabled”. It is not shown if ECO
Mode C1&C2 is congured.
15 ECO Mode C2 (*1) O O O O O O O
Available if Water Calculation modes for circuit 2 (Water calculation mode for
circuit 2 heating (C2WC) for heating or Water calculation mode for circuit 2
cooling (CC2WC) for cooling) are not set as “Disabled”. It is not shown if ECO
Mode C1&C2 is congured.
16 Forced OFF O O O O O O O Always
17 SG 2 O O O O O O O
Available if 8-200 (“Status” of Smart function in Optional functions menu) is
“Enabled” and 8-201 (“Smart Action” in System option of the Optional functions
menu) is set as “SM Grid Ready”
? NOTE
• (*1) When ECO Mode input function is used and a timer is congured with Eco periods take into account that conguration could be overwritten.
• These options cannot be repeated.
UNIT CONTROLLER
PMML0335A rev.1 - 04/2016
159