To Next PageTo Next Page
Need help?Do you have a question about the HITEC RDX 2 PRO and is the answer not in the manual?
General| Discharge Current | 0.1-2.0A |
|---|---|
| Discharge Power | 10W |
| Display Type | LCD |
| Input Voltage | 11-18V DC |
| Battery Types Supported | LiPo, LiFe, Li-ion, NiMH, NiCd, Pb |
| Number of Cells | 1-6S (LiPo/LiFe/Li-ion), 1-15S (NiMH/NiCd), 2-12V (Pb) |
| Charging Current | 0.1-10.0A |
| Charge Power | 100W |
| Balancing Current | 300mA per cell |
Essential warnings about unattended operation and environmental hazards for safe charging.
Key points to check before initiating battery charging for safe and effective operation.
Crucial warnings about selecting correct battery type and cell voltage to prevent fire or explosion.
Description of the main input buttons: CHANNEL, MODE/STOP, and ENTER/START.
Identifies XT60 output sockets, balance lead sockets, and USB ports on the charger.
Details the Jog Dial, Channel Button, and Mode/Stop Button for operation.
Features like battery memory, twin-channel charging, and integrated balancing for various lithium battery types.
Details Balance, Standard Charge, Fast Charge, and Storage modes for lithium battery packs.
Details Re-Peak, Cyclic, and Auto Charge modes for NiMH/NiCd batteries.
Covers Capacity Cut-Off, Safety Timer, USB charging, and Power Supply function.
Instructions for connecting the charger to AC or DC power sources.
Steps for connecting the battery, emphasizing correct parameter checks before connection.
Procedure for connecting the battery balance lead to the charger, ensuring correct polarity.
Guide to initial setup, including selecting the correct battery type and operation.
Overview of operations like Charge, Discharge, Storage, and Fast Charge for lithium batteries.
Details Charge, Auto Charge, Discharge, Re-Peak, and Cycle modes for NiMH/NiCd batteries.
Explains Normal, AGM, Cold Charge, and Discharge modes for Pb batteries.
How to use the Jog Dial for scrolling through menus and adjusting parameters.
Process for selecting the correct battery type and charge/discharge program.
Step-by-step guide for setting up and charging lithium battery packs.
Choosing charge modes and adjusting amperage/voltage based on battery specifications.
Verifying settings and initiating the charge process, including cell count checks.
Viewing real-time status like cell count, amperage, voltage, and capacity during charging.
How to stop the charging or discharging process at any time.
Selecting NiMH/NiCd battery type and accessing available charge modes.
Setting amperage and initiating the standard charge process for NiMH batteries.
Automatic charging for NiMH based on internal resistance and user-set maximum amperage.
Setting discharge rate and voltage cut-off for NiMH/NiCd batteries.
Topping off NiMH/NiCd batteries multiple times to ensure a full charge.
Performing automatic charge/discharge cycles to improve NiMH/NiCd battery performance.
Adjusting delta peak voltage sensitivity for NiMH/NiCd charge termination.
Configuring the safety timer duration for charging or discharging.
Selecting Pb battery type and accessing Normal, AGM, Cold, and Discharge modes.
Instructions for charging Lead-Acid batteries using Normal or AGM modes.
Specific charging procedure for Lead-Acid batteries at low temperatures.
Critical warning about selecting voltages over 12V to avoid damaging connected devices.
Steps to select and activate the DC power supply function for external devices.
Procedure for saving and recalling charge/discharge profiles for lithium battery types.
Final step to save the configured battery settings to memory.
Procedure for saving and recalling charge/discharge profiles for NiMH/NiCd battery types.
Procedure for saving and recalling charge/discharge profiles for Pb battery types.
Configuration for output voltage and current when using the power supply function.
Setting safety timer duration and maximum charge capacity limit.
Choosing display units and setting cool-down periods between cycles.
Adjusting delta peak voltage sensitivity for NiMH/NiCd charge termination.
Configuring audible feedback and DC input low voltage cut-off.
Restoring the charger to its original factory default settings.
How to enter the battery meter program to check voltage readings.
Displaying individual cell voltage and summary of pack voltage, highest, and lowest.
How to enter the battery resistance meter program.
Displaying individual cell and total battery internal resistance.
Covers errors like reverse polarity, connection breaks, incorrect connections, and input voltage issues.
Alerts for invalid cell settings or voltages, indicating potential battery or configuration problems.
Errors related to mode conflicts, overheating, and operational limits like time or capacity.
Alerts for cell voltage imbalance and reaching the maximum battery voltage.
Details FCC rules, conditions for operation, and RF exposure guidelines.
Disclaimer regarding charger usage, misuse, and Hitec RCD's limited liability.
Details the terms and conditions of the one-year limited warranty for the charger.
Instructions for obtaining service and repair for the Hitec charger, including website and shipping.
Warning about chemicals in the product known to cause cancer in California.
